AFBR-57M5APZ Avago Technologies US Inc., AFBR-57M5APZ Datasheet - Page 4

TXRX DGTL DIAGNOSTIC PLUG ETH

AFBR-57M5APZ

Manufacturer Part Number
AFBR-57M5APZ
Description
TXRX DGTL DIAGNOSTIC PLUG ETH
Manufacturer
Avago Technologies US Inc.
Datasheet

Specifications of AFBR-57M5APZ

Applications
Ethernet
Data Rate
2.125Gbps
Wavelength
860nm
Voltage - Supply
2.97 V ~ 3.63 V
Connector Type
LC Duplex
Mounting Type
SFP
Data Rate Max
2.125Gbps
Supply Voltage
3.3V
Wavelength Typ
850nm
Peak Reflow Compatible (260 C)
Yes
Leaded Process Compatible
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
516-1713
517-1713
517-1713

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AFBR-57M5APZ
Manufacturer:
Avago Technologies US Inc.
Quantity:
135
Part Number:
AFBR-57M5APZ
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Receiver Loss of Signal (Rx_LOS)
The post-amplification IC also includes transition
detection circuitry which monitors the ac level of
incoming optical signals and provides a TTL/CMOS
compatible status signal to the host (pin 8). An adequate
optical input results in a low Rx_LOS output while a high
Rx_LOS output indicates an unusable optical input. The
Rx_LOS thresholds are factory set so that a high output
indicates a definite optical fault has occurred. Rx_LOS
can also be monitored via the two-wire serial interface
(address A2h, byte 110, bit 1).
Functional Data I/O
The AFBR-57M5APZ interfaces with the host circuit
board through twenty I/O pins (SFP electrical connector)
identified by function in Table 2. The board layout for this
interface is depicted in Figure 6.
The AFBR-57M5APZ high speed transmit and receive
interfaces require SFP MSA compliant signal lines on
the host board. To simplify board requirements, biasing
resistors and ac coupling capacitors are incorporated into
the SFP transceiver module (per SFF-8074i) and hence are
not required on the host board. The Tx_Disable, Tx_Fault,
and Rx_LOS lines require TTL lines on the host board (per
SFF-8074i) if used. If an application chooses not to take
advantage of the functionality of these pins, care must be
taken to ground Tx_Disable (for normal operation).
Figure 2 depicts the recommended interface circuit to
link the AFBR-57M5APZ to supporting physical layer ICs.
Timing for MSA compliant control signals implemented
in the transceiver are listed in Figure 4.
Application Support
An Evaluation Kit and Reference Designs are available to
assist in evaluation of the AFBR-57M5APZ. Please contact
your local Field Sales representative for availability and
ordering details.
4
Caution
There are no user serviceable parts nor maintenance
requirements for the AFBR-57M5APZ. All mechanical
adjustments are made at the factory prior to shipment.
Tampering with, modifying, misusing or improp-
erly handling the AFBR-57M5APZ will void the product
warranty. It may also result in improper operation
and possibly overstress the laser source. Performance
degradation or device failure may result. Connection of
the AFBR-57M5APZ to a light source not compliant with
ANSI FC-PI or IEEE 802.3 specifications, operating above
maximum operating conditions or in a manner inconsis-
tent with it’s design and function may result in exposure
to hazardous light radiation and may constitute an act
of modifying or manufacturing a laser product. Persons
performing such an act are required by law to re-certify
and re-identify the laser product under the provisions of
U.S. 21 CFR (Subchapter J) and TUV.
Ordering Information
Please contact your local field sales engineer or one of
Avago Technologies franchised distributors for ordering
information. For technical information, please visit Avago
Technologies’ WEB page at www.Avago.com or contact
Avago Technologies Semicon-ductor Products Customer
Response Center at 1-800-235-0312. For information
related to SFF Committee documentation visit www.
sffcommittee.org.
Regulatory Compliance
The AFBR-57M5APZ complies with all applicable laws
and regulations as detailed in Table 1. Certification level
is dependent on the overall configuration of the host
equipment. The transceiver performance is offered as a
figure of merit to assist the designer.

Related parts for AFBR-57M5APZ