LTL-30EHJ Lite-On Electronics, LTL-30EHJ Datasheet
LTL-30EHJ
Specifications of LTL-30EHJ
LT1057
Available stocks
Related parts for LTL-30EHJ
LTL-30EHJ Summary of contents
Page 1
... All dimensions are in millimeters (inches). 2. Tolerance is ± 0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specification is subject to change without notice. Part No. : LTL-30EHJ BNS-OD-C131/ Lens White Diffused Source Color ...
Page 2
... Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Derating Linear From 50 ℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [2 mm(.078") From Body] Part No. : LTL-30EHJ BNS-OD-C131/ =25 ℃ ℃ ℃ ℃ A Red Orange 100 90 30 ...
Page 3
... International De L'Eclairage) eye-response curve. 2. θ is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 1/2 3. The dominant wavelength, λ wavelength which defines the color of the device. 4. The Iv guarantee should be added ± 15%. Part No. : LTL-30EHJ BNS-OD-C131/ =25 ℃ ℃ ℃ ℃ A Color Min. ...
Page 4
... LITE-ON TECHNOLOGY CORPORATION . Typical Electrical / Optical Characteristics Curves (25 ℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL-30EHJ BNS-OD-C131/ Page : ...
Page 5
... Inner cartons per outer carton total 40,000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL-30EHJ BNS-OD-C131/ Packing Spec Page : 5 ...
Page 6
... LITE-ON TECHNOLOGY CORPORATION . Bin Table Specification Luminous Intensity (Red Orange ) Unit: mcd @20mA IV Note: Tolerance of each bin limit is ±15% Luminous Intensity ( Green) Unit : mcd @20mA IV Note: Tolerance of each bin limit is ±15% Part No. : LTL-30EHJ BNS-OD-C131/ Min Min. 12 Max Max 100 Page : 6 of ...
Page 7
... LITE-ON TECHNOLOGY CORPORATION . Bin Table Specification Luminous Intensity ( Bin Code Min. 9 12.6 8 12 Note: Tolerance of each bin limit is ±15% Part No. : LTL-30EHJ BNS-OD-C131/ Green ) Unit : mcd @20mA Iv Green Max 100 100 100 Red Orange Luminous Intensity ( Unit : mcd @20mA Iv Red Orange Min. Max. 14 ...
Page 8
... Soldering time 3 sec. Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL-30EHJ BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION . CAUTIONS Pre-heat ...
Page 9
... To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTL-30EHJ BNS-OD-C131/ Circuit model B ...
Page 10
... No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL-30EHJ BNS-OD-C131/ Page : 10 of ...
Page 11
... Shock Environmental Test Solder Resistance Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL-30EHJ BNS-OD-C131/ Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) ° Ta= 65±5 C RH= 90 ～ ...