LTL-30EHJ Lite-On Electronics, LTL-30EHJ Datasheet - Page 8

• Manufacturer Part Number: LTL-30EHJ
• Description: LED 5MM GREEN/RED BICOLOR 3LEAD
• Manufacturer: Lite-On Electronics
• Type: Bi-Colorr

Specifications of LTL-30EHJ

• Led Size: T-1 3/4
• Lens Color/style: Diffused
• Operating Voltage: 2.6 V
• Operating Current: 100 mA
• Lens Shape: Dome
• Mounting Style: Through Hole
• Viewing Angle: 30°
• Package / Case: Radial - 3 Lead
• Color: Green, Orange-Red
• Millicandela Rating: 29mcd Green, 40mcd Orange-Red
• Current - Test: 20mA
• Wavelength - Dominant: 569nm, 621nm
• Wavelength - Peak: 565nm, 630nm
• Voltage - Forward (vf) Typ: 2.1V Green, 2V Orange-Red
• Lens Type: Diffused, White
• Lens Style/size: Round, 5mm, T-1 3/4
• Height: 8.60mm
• Mounting Type: Through Hole
• Resistance Tolerance: 569nm, 621nm
• Package Type: T-1 3/4
• Emitting Color: Yellow Green/Red
• Luminous Intensity: 29/40mcd
• Test Current (it): 20mA
• Forward Current: 30mA
• Dominant Wave Length: 572/625nm
• Forward Voltage: 2.6V
• Product Length (mm): 5.85mm
• Product Height (mm): 8.6mm
• Product Depth (mm): 5.85mm
• Mounting: Through Hole
• Peak Wavelength: 565/630nm
• Shape Type: Circular
• Chip Material: GaP/GaAsP
• Main Category: Standard LED
• Number Of Elements: 2
• Pin Count: 3
• Operating Temperature Classification: Industrial
• Operating Temp Range: -55C to 100C
• Reverse Voltage: 5V
• Power Dissipation: 100mW
• Lens Dimensions: 5x5x7.6mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Luminous Flux @ Current - Test: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 160-1057; LT1057

1. Application
2. Storage
3. Cleaning
4. Lead Forming & Assembly
5. Soldering
Part No. : LTL-30EHJ
BNS-OD-C131/A4
During lead forming, the leads should be bent at a point at least 3mm from the base of LED lens.
Do not use the base of the leadframe as a fulcrum during forming.
Lead forming must be done before soldering, at normal temperature.
During assembly on PCB, use minimum clinch force possible to avoid excessive mechanical stress.
When soldering, For Lamp without stopper type and must be leave a minimum of 3 mm clearance
To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, Dipping the
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity.
It is recommended that LEDs out of their original packaging are used within three months.
For extended storage out of their original packaging, it is recommended that the LEDs be stored in
a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LEDs if necessary.
from the base of the lens to the soldering point.
lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high temperature.
The LEDs described here are intended to be used for ordinary electronic equipment (such as office
equipment,
advance for information on applications in which exceptional reliability is required, particularly when
the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation,
transportation, traffic control equipment, medical and life support systems and safety devices).
Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or
Recommended soldering conditions :
Temperature
Soldering time
product.
catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp
Soldering iron
communication equipment and household applications).Consult Liteon’s Sales in
300°C Max.
3 sec. Max.
(one time only)
LITE-ON TECHNOLOGY CORPORATION .
P r o p e r t y o f L i t e - O n O n l y
CAUTIONS
Pre-heat
Pre-heat time
Solder wave
Soldering time
Wave soldering
100°C Max.
60 sec. Max.
260°C Max.
5 sec. Max.
Page :
8
of
11