HLMP-AB61-RU0ZZ Avago Technologies US Inc., HLMP-AB61-RU0ZZ Datasheet - Page 10
![LED 5MM INGAN BLUE 30X70DEG](/photos/26/78/267853/hlmp_ab_am-lb-lmxx_wht_sml.jpg)
HLMP-AB61-RU0ZZ
Manufacturer Part Number
HLMP-AB61-RU0ZZ
Description
LED 5MM INGAN BLUE 30X70DEG
Manufacturer
Avago Technologies US Inc.
Datasheet
1.HLMP-AD61-X1TZZ.pdf
(13 pages)
Specifications of HLMP-AB61-RU0ZZ
Viewing Angle
30°, 70°
Package / Case
Radial - 2 Lead
Color
Blue
Luminous Flux @ Current - Test
600 mlm
Millicandela Rating
850mcd
Current - Test
20mA
Wavelength - Dominant
470nm
Wavelength - Peak
464nm
Voltage - Forward (vf) Typ
3.2V
Lens Type
Diffused, Blue Tinted
Lens Style/size
Oval, 5mm
Height
8.70mm
Mounting Type
Through Hole
Resistance Tolerance
470nm
Led Size
T-1 3/4
Illumination Color
Blue
Lens Color/style
Blue
Wavelength
470 nm
Mounting Style
Through Hole
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Precautions:
Lead Forming:
• The leads of an LED lamp may be preformed or cut to
• For better control, it is recommended to use proper
• If manual lead cutting is necessary, cut the leads after
Soldering and Handling:
• Care must be taken during PCB assembly and solder-
• LED component may be effectively hand soldered to
• ESD precaution must be properly applied on the sol-
• Recommended soldering condition:
Note:
1) Above conditions refers to measurement with thermocouple
2) It is recommended to use only bottom preheaters in order to reduce
• Wave soldering parameters must be set and main-
10
length prior to insertion and soldering on PC board.
tool to precisely form and cut the leads to applicable
length rather than doing it manually.
the soldering process. The solder connection forms a
mechanical ground which prevents mechanical stress
due to lead cutting from traveling into LED package.
This is highly recommended for hand solder operation,
as the excess lead length also acts as small heat sink.
ing process to prevent damage to the LED compo-
nent.
PCB. However, it is only recommended under unavoid-
able circumstances such as rework. The closest manual
soldering distance of the soldering heat source (sol-
dering iron’s tip) to the body is 1.59mm. Soldering the
LED using soldering iron tip closer than 1.59mm might
damage the LED.
dering station and personnel to prevent ESD damage
to the LED component that is ESD sensitive. Do refer
to Avago application note AN 1142 for details. The sol-
dering iron used should have grounded tip to ensure
electrostatic charge is properly grounded.
mounted at the bottom of PCB.
thermal stress experienced by LED.
tained according to the recommended temperature
and dwell time. Customer is advised to perform daily
check on the soldering profile to ensure that it is al-
ways conforming to recommended soldering condi-
tions.
Pre-heat temperature
Preheat time
Peak temperature
Dwell time
Wave
Soldering
105 °C Max.
60 sec Max
250 °C Max.
3 sec Max.
1.59mm
[1, 2]
Manual Solder
Dipping
-
-
260 °C Max.
5 sec Max
Note:
1. PCB with different size and design (component density) will have
2. Avago Technologies’ high brightness LED are using high efficiency
Avago Technologies LED configuration
• Any alignment fixture that is being applied during
• At elevated temperature, LED is more susceptible to
• If PCB board contains both through hole (TH) LED and
• Recommended PC board plated through holes (PTH)
• Over-sizing the PTH can lead to twisted LED after
different heat mass (heat capacity). This might cause a change in
temperature experienced by the board if same wave soldering
setting is used. So, it is recommended to re-calibrate the soldering
profile again before loading a new type of PCB.
LED die with single wire bond as shown below. Customer is advised
to take extra precaution during wave soldering to ensure that the
maximum wave temperature does not exceed 250°C and the solder
contact time does not exceeding 3sec. Over-stressing the LED dur-
ing soldering process might cause premature failure to the LED due
to delamination.
Note: Electrical connection between bottom surface of LED die and
the lead frame is achieved through conductive paste.
wave soldering should be loosely fitted and should
not apply weight or force on LED. Non metal mate-
rial is recommended as it will absorb less heat during
wave soldering process.
mechanical stress. Therefore, PCB must allowed to cool
down to room temperature prior to handling, which
includes removal of alignment fixture or pallet.
other surface mount components, it is recommended
that surface mount components be soldered on the
top side of the PCB. If surface mount need to be on the
bottom side, these components should be soldered
using reflow soldering prior to insertion the TH LED.
size for LED component leads.
clinching. On the other hand under sizing the PTH can
cause difficulty inserting the TH LED.
LED component
lead size
0.45 x 0.45 mm
(0.018x 0.018 inch)
0.50 x 0.50 mm
(0.020x 0.020 inch)
AlInGaP Device
CATHODE
Diagonal
0.636 mm
(0.025 inch)
0.707 mm
(0.028 inch)
ANODE
InGaN Device
Plated through
hole diameter
0.98 to 1.08 mm
(0.039 to 0.043 inch)
1.05 to 1.15 mm
(0.041 to 0.045 inch)