QW050A1 Lineage Power, QW050A1 Datasheet - Page 10

• Manufacturer Part Number: QW050A1
• Description: CONVERTER DC/DC 5V 50W OUT
• Manufacturer: Lineage Power
• Series: QWr
• Type: Isolated with Remote On/Offr

Specifications of QW050A1

• Output: 5V
• Number Of Outputs: 1
• Power (watts): 50W
• Mounting Type: Through Hole
• Voltage - Input: 36 ~ 75V
• Package / Case: 8-DIP Module
• 1st Output: 5 VDC @ 10A
• Size / Dimension: 2.28" L x 1.45" W x 0.50" H (57.9mm x 36.8mm x 12.7mm)
• Power (watts) - Rated: 50W
• Operating Temperature: -40°C ~ 100°C
• Efficiency: 84%
• Approvals: CE, CSA, UL, VDE
• Output Current: 10A
• Input Voltage: 48V
• Output Voltage: 5V
• Output Power: 50
• Screening Level: Industrial
• Operating Temperature Min Deg. C: -40C
• Operating Temperature Max Deg. C: 100C
• Product Length (mm): 36.8mm
• Product Depth (mm): 57.9mm
• Product Height (mm): 12.7mm
• Mounting Style: Through Hole
• Pin Count: 8
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Lead Free Status / Rohs Status: RoHS Not Applicable

dc-dc Converters; 36 to 75 Vdc Input, 5 Vdc Output; 50 W and 75 W
Feature Descriptions
Remote Sense
Figure 17. Effective Circuit Configuration for
Output Voltage Set-Point Adjustment
(Trim)
Output voltage trim allows the user to increase or
decrease the output voltage set point of a module. This
is accomplished by connecting an external resistor
between the TRIM pin and either the SENSE(+) or
SENSE(–) pins. The trim resistor should be positioned
close to the module.
If not using the trim feature, leave the TRIM pin open.
With an external resistor between the TRIM and
SENSE(–) pins (R
(V
tion determines the required external-resistor value to
obtain a percentage output voltage change of ý%.
The test results for this configuration are displayed in
Figure 19. This figure applies to all output voltages.
With an external resistor connected between the TRIM
and SENSE(+) pins (R
point (V
The following equation determines the required exter-
nal-resistor value to obtain a percentage output voltage
change of ý%.
The test results for this configuration are displayed in
Figure 21.
The voltage between the V
must not exceed the minimum output overvoltage pro-
tection value shown in the Feature Specifications table.
This limit includes any increase in voltage due to
10
10
O, adj
SUPPLY
R
R
RESISTANCE
adj-down
adj-up
) decreases (see Figure 18). The following equa-
CONTACT
O, adj
=
Single-Module Remote-Sense Operation
) increases (see Figure 20).
I
I
=
⎛
⎝
5.1V
---------------------------------------------- -
⎛
⎝
510
--------- - 10.2
Δ%
adj-down
V
V
1.225Δ%
(continued)
I
I
O
(-)
(+)
(
–
100
SENSE(+)
adj-up
SENSE(–)
), the output voltage set point
V
V
+
O
O
), the output voltage set
⎞
⎠
O
(+)
(+) and V
Δ%
(–)
(continued)
kΩ
)
–
DISTRIBUTION LOSSES
I
510
--------- -
Δ%
O
CONTACT AND
O
(–) terminals
–
10.2
LOAD
⎞ kΩ
⎠
8-651 (C).m
remote-sense compensation and output voltage set-
point adjustment (trim). See Figure 17.
Although the output voltage can be increased by both
the remote sense and by the trim, the maximum
increase for the output voltage is not the sum of both.
The maximum increase is the larger of either the
remote sense or the trim. Consult the factory if you
need to increase the output voltage more than the
above limitation.
The amount of power delivered by the module is
defined as the voltage at the output terminals multiplied
by the output current. When using remote sense and
trim, the output voltage of the module can be
increased, which at the same output current would
increase the power output of the module. Care should
be taken to ensure that the maximum output power of
the module remains at or below the maximum rated
power.
Figure 18. Circuit Configuration to Decrease
Figure 19. Resistor Selection for Decreased
100k
10k
1M
1k
V
ON/OFF
CASE
V
I
I
(+)
(–)
0
Output Voltage
Output Voltage
% CHANGE IN OUTPUT VOLTAGE (Δ %)
SENSE(+)
SENSE(–)
10
V
TRIM
V
O
O
(+)
(–)
20
R
adj-down
Lineage Power
30
April 2008
R
LOAD
8-748 (C).b
8-2577 (C)
40