VPOL16A-12-SIP CUI Inc, VPOL16A-12-SIP Datasheet - Page 10
![CONVERTR DC/DC .75/5VOUT 16A SIP](/photos/8/69/86973/mfg_vpol16a-12-sip_sml.jpg)
VPOL16A-12-SIP
Manufacturer Part Number
VPOL16A-12-SIP
Description
CONVERTR DC/DC .75/5VOUT 16A SIP
Manufacturer
CUI Inc
Series
V-Infinity VPOL16Ar
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.VPOL16A-12-SIP.pdf
(12 pages)
Specifications of VPOL16A-12-SIP
Output
0.75 ~ 5V
Number Of Outputs
1
Power (watts)
80W
Mounting Type
Through Hole
Voltage - Input
9 ~ 14V
Package / Case
11-SIP Module (10 Leads)
1st Output
0.75 ~ 5 VDC @ 16A
Size / Dimension
2.00" L x 0.33" W x 0.51" H (50.8mm x 8.4mm x 13mm)
Power (watts) - Rated
80W
Operating Temperature
-40°C ~ 85°C
Efficiency
94%
Approvals
cUL, UL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Other names
102-1293
PART NUMBER: VPOL16A-12-SIP
7.6 Input Capacitance at the Power Module
The VPOL16A-12-SIP converters must be connected to a low AC
source impedance. To avoid probl ems with loop stability source
inductance should be low. Also, the input capacitors should be placed
close to the converter input pins to de-couple distribution inductance.
However, the external input capacitors are chosen for suitable ripple
handling capability. Low ESR polymers are a good choice. They have
high capacitance, high ripple rating and low ESR (typical <100mohm).
Electrolytic capacitors should be avoided. Circuit as shown in Figure 10
represents typical measurement methods for ripple current. Input
reflected-ripple current is measured with a simulated source Inductance
of 1uH. Current is measured at the input of the module.
7.7 Test Set-Up
The basic test set-up to measure parameters such as efficiency and
load regulation is shown in Figure 11. Things to note are that this
converter is non-isolated, as such the input and output share a common
ground. These grounds should be connected together via low
impedance ground plane in the application circuit. When testing a
converter on a bench set-up, ensure that -V
together via a low impedance short to ensure proper efficiency and load
regulation measurements are being made. When testing the V-Infinity’s
VPOL16A-12-SIP series under any transient conditions please ensure
that the transient response of the source is sufficient to power the
equipment under test. We can calculate the
The value of efficiency is defined as:
Where: Vo is output voltage,
The value of load regulation is defined as:
Power
Supply
ç =
Load
20050 SW 112
Efficiency
Load regulation and line regulation.
To Oscilloscope
Vin
Vo
Figure 10. Input Reflected-Ripple Test Setup
Vin is input voltage,
Iin is input current.
.
Io is output current,
reg=
+
x
x
Io
Iin
V
x
FL
220uF
ESR<0.1ohm
100
V
th
_
NL
L1
1uH
V
Ave. Tualatin, Oregon 97062
%
NL
Tantalum
x
2*100uF
100
%
in
and -V
o
+Vin
Common
VPOL16A-12-SIP
are connected
phone
phone 503.612.2300 fax
DESCRIPTION: point of load converter
Power
Supply
Where: V
The value of line regulation is defined as:
Where: V
7.8 Remote Sense Compensation
Remote Sense regulates the output voltage at the point of load. It
minimizes the effects of distribution losses such as drops across the
connecting pin and PCB tracks (see Figure 12). Please note however,
the maximum drop from the output pin to the point of load should not
exceed 500mV for remote compensation to work.
The amount of power delivered by the module is defined as the output
voltage multiplied by the output current (VO x IO).
When using TRIM UP, the output voltage of the module will increase
which, if the same output current is maintained, increases the power
output by the module. Make sure that the maximum output power of the
module remains at or below the maximum rated power.
disconnected.
Figure 12. Circuit Configuration for Remote Sense Operation
When the Remote Sense feature is not being used, leave sense pin
+
Current Meter
V
Voltage Meter
Figure 11. VPOL16A-12-SIP Series Test Setup
LL
V
HL
A
+Vin
Common
FL
NL
is the output voltage of minimum input voltage at full load.
is the output voltage of maximum input voltage at full load.
is the output voltage at full load
is the output voltage at no load
Line
fax 503.612.2382
V
100uF
.
reg=
Common
+Sense
V
HL
+Vo
+Vin
Common
VPOL16A-12-SIP
V
_
LL
V
LL
Distribution Losses
Distribution Losses
Common
x
+Sense
100
+Vo
rev.
page
date
%
R-Load
V
01/2008
10 of 12
A
Load