VPOL16A-12-SIP CUI Inc, VPOL16A-12-SIP Datasheet - Page 2
![CONVERTR DC/DC .75/5VOUT 16A SIP](/photos/8/69/86973/mfg_vpol16a-12-sip_sml.jpg)
VPOL16A-12-SIP
Manufacturer Part Number
VPOL16A-12-SIP
Description
CONVERTR DC/DC .75/5VOUT 16A SIP
Manufacturer
CUI Inc
Series
V-Infinity VPOL16Ar
Type
Point of Load (POL) Non-Isolatedr
Datasheet
1.VPOL16A-12-SIP.pdf
(12 pages)
Specifications of VPOL16A-12-SIP
Output
0.75 ~ 5V
Number Of Outputs
1
Power (watts)
80W
Mounting Type
Through Hole
Voltage - Input
9 ~ 14V
Package / Case
11-SIP Module (10 Leads)
1st Output
0.75 ~ 5 VDC @ 16A
Size / Dimension
2.00" L x 0.33" W x 0.51" H (50.8mm x 8.4mm x 13mm)
Power (watts) - Rated
80W
Operating Temperature
-40°C ~ 85°C
Efficiency
94%
Approvals
cUL, UL
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
3rd Output
-
2nd Output
-
Other names
102-1293
PART NUMBER: VPOL16A-12-SIP
1. Introduction
This application note describes the features and functions of V-Infinity’s
VPOL16A-12-SIP series of Non Isolated DC-DC Converters. These are
highly efficient, reliable and compact, high power density, single output
DC/DC converters. These “Point of Load” modules serve the needs
specifically of the fixed and mobile telecommunications and computing
market, employing economical distributed Power Architectures. The
VPOL16A-12-SIP series provide precisely regulated output voltage
range from 0.75V to 5.0Vdc over a wide range of input voltage (Vi=9.0 –
14Vdc) and can operate over an ambient temperature range of –40°C
to +85°C. Ultra-high efficiency operation is achieved through the use of
synchronous rectification and drive control techniques.
The modules are fully protected against short circuit and over-
temperature conditions. V-Infinity’s world class automated
manufacturing methods, together with an extensive testing and
qualification program, ensure that all VPOL16A-12-SIP series
converters are extremely reliable.
3. General Description
3.1 Electrical Description
A block diagram of the VPOL16A-12-SIP Series converter is shown in
Figure 1. Extremely high efficiency power conversion is achieved
through the use of synchronous rectification and drive techniques.
Essentially, the powerful VPOL16A-12-SIP series topology is based on
a non-isolated synchronous buck converter. The control loop is
optimized for unconditional stability, fast transient response and a very
tight line and load regulation. In a typical pre-bias application the
VPOL16A-12-SIP series converters do not draw any reverse current at
start-up. The output voltage can be adjusted from 0.75 to 5.0vdc, using
the TRIM pin with a external resistor. The converter can be shut down
via a remote ON/OFF input that is referenced to ground. This input is
compatible with popular logic devices; a 'positive' logic input is supplied
as standard. Positive logic implies that the converter is enabled if the
remote ON/OFF input is high (or floating), and disabled if it is low.
2.
Features
5.0Vdc
High efficiency topology, typically 94% at 5.0Vdc
Industry standard footprint
Wide ambient temperature range, -40°C to +85°C
Cost efficient open frame design
Programmable output voltage via external resistor from 0.75 to
No minimum load requirement (Stable at all loads)
Remote sense compensation
Fixed switching frequency
Continuous short-circuit protection and over current protection
Over-temperature protection (OTP)
Monotonic Startup with pre-bias at the output.
Remote ON/OFF
UL/IEC/EN60950 Certified.
20050 SW 112
VPOL16A-12-SIP
th
Ave. Tualatin, Oregon 97062
Converter
phone
phone 503.612.2300 fax
DESCRIPTION: point of load converter
The converter is also protected against over-temperature conditions. If
the converter is overloaded or the ambient temperature gets too high,
the converter will shut down to protect the unit.
3.2 Thermal Packaging and Physical Design.
The VPOL16A-12-SIP series uses a multi-layer FR4 PCB construction.
All surface mount power components are placed on one side of the
PCB, and all low-power control components are placed on the other
side. Thus, the Heat dissipation of the power components is optimized,
ensuring that control components are not thermally stressed. The
converter is an open-frame product and has no case or case pin. The
open-frame design has several advantages over encapsulated closed
devices. Among these advantages are:
ON/OFF
+VIN
COM
C1
heat generating components without heating more sensitive, small
signal control components.
re-cycled.
construction.
offers high reliability and easy diagnostics.
Efficient Thermal Management: the heat is removed from the
Environmental: Lead free open-frame converters are more easily
Cost Efficient: No encapsulation. Cost efficient open-frame
Reliable: Efficient cooling provided by open frame construction
Figure 1. Electrical Block Diagram
Q1
fax 503.612.2382
PWM IC
ERR AMP
Q2
D1
L1
C2
rev.
page
date
R sense
R1
R2
R trim
01/2008
2 of 12
+VO
+SENSE
COM
TRIM