MX5A-3-5SA Bourns Inc., MX5A-3-5SA Datasheet
![no-image](/images/manufacturer_photos/0/1/104/bourns_inc__sml.jpg)
MX5A-3-5SA
Specifications of MX5A-3-5SA
Related parts for MX5A-3-5SA
MX5A-3-5SA Summary of contents
Page 1
... Description ® Bourns MX5A-3-5SA is a non-isolated DC-DC converter offering designers a cost and space-efficient solution with standard features such as remote on/off, precisely regulated programmable output voltage and overcurrent and over- temperature protection. These modules deliver output current with full load efficiency 3.3 V output. ...
Page 2
... MX5A-3-5SA SMT Non-Isolated Power Module Electrical Specifications (Continued) Characteristic Output Voltage Setpoint Accuracy Output Voltage Tolerance Voltage Adjustment Range Line Regulation Load Regulation Temperature Regulation Output Current Output Current Limit Inception (Hiccup Mode) Output Short Circuit Current Output Ripple and Noise Voltage ...
Page 3
... MX5A-3-5SA SMT Non-Isolated Power Module Feature Specifications Characteristic Remote Enable Open = On (Logic Low) Low = Off (Logic High) Turn-On Delay and Rise Times Case 1: On/Off Low – Applied Case Applied, then On/Off Set Low Case 3: Output Voltage Rise Output Voltage Overshoot Overtemperature Protection ...
Page 4
... MX5A-3-5SA SMT Non-Isolated Power Module Characteristic Curves The curves provided below are typical characteristics for the MX5A-3-5SA modules at 25 °C. For any specific test configurations or any specific test requests, please contact Bourns. 95.0 90.0 85.0 80.0 75.0 70.0 1.0 1.5 2.0 2 ...
Page 5
... MX5A-3-5SA SMT Non-Isolated Power Module Characteristic Curves (Continued) 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 -0.5 1.5 Input Voltage (V ) Fig. 7 Input Voltage vs. I and 2 5 Load: 20 mVolt 2.5 µs Half Load: 20 mVolt 2.5 µs Full Load: 20 mVolt 2.5 µs Time (2.5 µ ...
Page 6
... MX5A-3-5SA SMT Non-Isolated Power Module Characteristic Curves (Continued) ??? ??? Output Voltage: 100 mVolt 10 µs Output Current (1.5 A/Div): 2 Volt 10 µs Time (10 µs/div) Fig. 13 Transient Response - 2.5 A Step ( 2x100 µF Polymer Capacitors ext ?? ?? Output Voltage: 500 mVolt 1 ms On/Off Voltage: 2 Volt 1 ms Time (1 ms/div) Fig ...
Page 7
... MX5A-3-5SA SMT Non-Isolated Power Module Characteristic Curves (Continued) 6 100 LFM Ambient Temperature (°C) Fig. 19 Derating Output Current vs. Local Ambient Temp. and Airflow ( 100 LFM Ambient Temperature (°C) Fig. 20 Derating Output Current vs. Local Ambient Temp. and Airflow ( Specifications are subject to change without notice. ...
Page 8
... Remote On/Off The MX5A-3-5SA comes standard with Active LOW with Negative On/Off logic, i.e., OPEN or LOW (< 0.4 V) will turn ON the device. To turn the device OFF, increase the voltage level above 2.4 V, placing the part into low dissipation sleep mode. The signal level of the On/Off pin input is defined with respect to ground ...
Page 9
... If left open circuit the output voltage will default to 0.75 Vdc. The correct Rtrim value for a specific voltage can be calculated using the following equation: Rtrim = [21.07/(Vo-0.7525)-5.11] KΩ For example, to set the MX5A-3-5SA to 3.3 V the following Rtrim resistor must be used: Rtrim = [21.07/(3.3-0.7525)-5.11] KΩ ...
Page 10
... MX5A-3-5SA SMT Non-Isolated Power Module Operating Information (Continued) Voltage Margining Output voltage margining can be implemented as follows: 1) Trim-up: Connect a resistor, Rm-up, from the Trim pin to the ground pin for adjusting the voltage upwards, and 2) Trim-down: Connect a resistor, Rm-down, from the Trim pin to the output pin for adjusting the voltage downwards. ...
Page 11
... Coplanarity The MX5A-3-5SA device has a maximum coplanarity of 100 µm (approx. 0.004 ”), as defined by JESD22-B108. Pin Plating Composition Tin (Sn) plating over nickel (Ni). Recommended Pad Layout Specifications are subject to change without notice. Customers should verify device performance in their specific applications. ...
Page 12
... MX5A-3-5SA SMT Non-Isolated Power Module Use in Manufacturing Environment Pick and Place Information Bourns SMT devices, packaged on tape and reel, are designed (low mass) for automated assembly using standard SMT pick and place equipment. The centrally located inductor provides the flat surface area to be used for component pick up. Variables such as nozzle style, nozzle size, handling speed, and placement pressure need to be optimized for best results ...
Page 13
... MX5A-3-5SA SMT Non-Isolated Power Module Use in Manufacturing Environment (Continued) Soldering Requirements Bourns recommends the following temperature profile for use on tin lead solder (Sn-Pb Eutectic) and lead free solder. For lead free solder, the maximum temperature during the mounting process should not exceed 245 °C. Sufficient time must be allowed to fuse the plating on the connection to ensure a reliable solder joint. However, the time above 230 ° ...