KSZ8851SNL-BBE-EVAL Micrel Inc, KSZ8851SNL-BBE-EVAL Datasheet - Page 29

• Manufacturer Part Number: KSZ8851SNL-BBE-EVAL
• Description: BOARD EVAL MAC/PHY FOR KSZ8851
• Manufacturer: Micrel Inc
• Series: LinkMD®r

Specifications of KSZ8851SNL-BBE-EVAL

• Design Resources: BeagleBoard Zippy2
• Main Purpose: Interface, Ethernet Controller (PHY and MAC)
• Embedded: No
• Utilized Ic / Part: KSZ8851SNL
• Primary Attributes: 1 Port, 100BASE-TX/10BASE-T
• Secondary Attributes: SPI Interface, LinkMD Cable Diagnostics
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 576-3602; KSZ8851SNL-BBE-EVL; ZIPPY2

Receive Queue (RXQ) Frame Format
The frame format for the receive queue is shown in Table 10. The first word contains the status information for the frame
received. The second word is the total number of bytes of the RX frame. Following that is the packet data area. The
packet data area holds the frame itself. It includes the CRC checksum.
Frame Receiving Path Operation in RXQ
This section describes the typical register settings for receiving packets from KSZ8851SNL to host processor with generic
bus interface. User can use the default value for most of the receive registers. The following Table 11 describes all
registers which need to be set and used for receiving single or multiple frames.
August 2009
Register Name[bit](offset)
RXCR1(0x74)
RXCR2(0x76)
RXFHSR[15:0](0x7C)
RXFHBCR[11:0](0x7E)
RXQCR[12:3](0x82)
RXFDPR[14](0x86)
RXDTTR[15:0](0x8C)
RXDBCTR[15:0](0x8E)
IER[13](0x90)
ISR[15:0](0x92)
RXFCTR[15:8](0x9C)
RXFCTR[7:0](0x9C)
Micrel, Inc.
Description
Set receive control function as below:
Set RXCR1[10] to enable receiving flow control. Set RXCR1[0] to enable receiving block operation.
Set receive checksum check for ICMP, UDP, TCP and IP packet.
Set receive address filtering scheme as shown in the Table 3.
Set bit 3 to start DMA access from host CPU either read (receive frame data) or write (transmit data
frame). Set bit 4 to automatically enable RXQ frame buffer dequeue. Set bit 5 to enable RX frame count
threshold and read bit 10 for status. Set bit 6 to enable RX data byte count threshold and read bit 11 for
status. Set bit 7 to enable RX frame duration timer threshold and read bit 12 for status. Set bit 9 enable
RX IP header two-byte offset.
threshold in 1 uS interval count and bit 7 of RXQCR register is set to 1, the KSZ8851SNL will generate
RX interrupt in ISR[13] and indicate the status in RXQCR[12].
threshold in byte count and bit 6 of RXQCR register is set to 1, the KSZ8851SNL will generate RX
interrupt in ISR[13] and indicate the status in RXQCR[11].
interrupt (bit 13 in ISR) occurred.
threshold value and bit 5 of RXQCR register is set to 1, the KSZ8851SNL will generate RX interrupt in
ISR[13] and indicate the status in RXQCR[10].
This register (read only) indicates the current received frame header status information.
This register (read only) indicates the current received frame header byte count information.
Set RXQ control function as below:
Set bit 14 to enable RXQ address register increments automatically on accesses to the data register.
To program received frame duration timer value. When Rx frame duration in RXQ exceeds this
To program received data byte count value. When the number of received bytes in RXQ exceeds this
Set bit 13 to enable receive interrupt in Interrupt Enable Register.
Write 1 (0xFFFF) to clear all interrupt status bits after interrupt occurred in Interrupt Status Register.
Rx frame count read only. To indicate the total received frame in RXQ frame buffer when receive
To program received frame count value. When the number of received frames in RXQ exceeds this
Packet Memory
Address Offset
0
2
4 - up
Table 11. Registers Setting for Receive Function Block
Table 10. Frame Format for Receive Queue
Bit 15
2
Status Word
(see description in RXFHSR register)
Byte Count
(see description in RXFHBCR register)
Receive Packet Data
(maximum size is 2000)
nd
Byte
29
1
st
Bit 0
Byte
KSZ8851SNL/SNLI
M9999-083109-2.0