CBC-EVAL-08 Cymbet Corporation, CBC-EVAL-08 Datasheet - Page 2

• Manufacturer Part Number: CBC-EVAL-08
• Description: ENERCHIP EH SEH EVAL KIT
• Manufacturer: Cymbet Corporation
• Series: EnerChip™ EHr
• Type: Energy Harvestingr

Specifications of CBC-EVAL-08

• Main Purpose: Power Management, Renewable Energy
• Embedded: No
• Utilized Ic / Part: CBC5300
• Primary Attributes: Thin Film Rechargeable Solid State Battery
• Secondary Attributes: Solar Energy Harvester
• Input Voltage: 4.06 V
• Output Voltage: 3.55 V
• Board Size: 90.2 mm x 50.8 mm
• Maximum Operating Temperature: +70 C
• Minimum Operating Temperature: 0 C
• Product: Power Management Modules
• Dimensions: 90.2 mm x 50.8 mm
• Lead Free Status / RoHS Status: Request inventory verification / Request inventory verification
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Request inventory verification / Request inventory verification
• Other names: 859-1002

CBC-EVAL-08 Module Connectors
EVAL-08 Module Connector Explanations
J1 Connector
module. (For reference, header connector J1 is Mill-Max p/n 850-10-006-20-001000; the socket it mates to is
Mill-Max p/n 851-93-006-20-001000.)
J5 Connector
module. (For reference, header connector J5 is a 5-pin section of Samtec 50-pin header p/n TSW-150-07-G-S.
J7 Connector
J8 Jumper and Shunt
is removed before CBC-EVAL-08 is charged for the first time. This connector can also be used to connect an
alternate solar panel to CBC-EVAL-08.
PT1 Connector
It can be connected in parallel with the CBC-EVAL-08 solar panel by leaving J7 intact. Or, the piezoelectric
transducer can be used stand-alone by cutting the J7 trace.
Cable Assembly
facilitate connection between the J5 connector and a 5-pin header on the user’s board.
DS-72-08 Rev18
Connector Type: Rt. Angle SIP
Pin Number(s)
J1 Connector for User
1
2
3
4
5
6
Solar Panel
- Power and handshaking signals for connection to a target board - e.g. wireless end-point
- Power and handshaking signal pins for connection to a target board - e.g. wireless end-point
- This trace is to be cut if an alternate solar panel is to be connected to J8.
- An alternate piezoelectric (or other AC) energy harvesting transducer can be connected.
Designation
Connected
Connected
- A 5-conductor cable with a header connector at each end is provided with CBC-EVAL-08 to
BATOFF
CHARGE
©2009 Cymbet Corporation • Tel: [phone] • www.cymbet.com
GND
V
Not
Not
OUT2
- This connector ships with the shunt installed to protect the EH module. The shunt
EnerChip
J7 J8
Figure 3: EnerChip EVAL-08 Connections
Module
Pin Number(s)
5300
EnerChip Solar Energy Harvesting Demo Kit
PT1
Pin Number(s)
EH
Connector Type: Vertical SIP
Connector Type: Trace Vias
J5 Connector for User
1
2
1
2
3
4
5
PT1 Connector
J5
1
Piezo input 1
Piezo input 2
1
Designation
Designation
CHARGE
BATOFF
V
J1
GND
V
OUT2
BAT
The CBC-EVAL-08 and CBC5300 modules are
sensitive to electrostatic discharge (ESD) and
must be handled accordingly. In cases where the
CBC-EVAL-08 or CBC5300 modules are removed
from their original packaging, it is a requirement
to maintain the same type of anti-static, non-
conductive packaging to prevent discharge of the
on-board EnerChips. Do not store the CBC-EVAL-08
or CBC5300 modules in conductive black foam, as
it will discharge and destroy the EnerChips on the
CBC5300 module.
Pin Number(s)
Pin Number(s)
Connector Type: Circular pad and
Connector Type: Trace Vias
1
1
2
J7 Connector
J8 Connector
trace
Cut Trace to use
external source
Positive input
Designation
Description
GND
Page 2 of 11