ISL54206AEVAL1Z Intersil, ISL54206AEVAL1Z Datasheet - Page 3

• Manufacturer Part Number: ISL54206AEVAL1Z
• Description: EVALUATION BOARD FOR ISL54206A
• Manufacturer: Intersil

Specifications of ISL54206AEVAL1Z

• Main Purpose: Interface, Analog & Digital Switch
• Embedded: No
• Utilized Ic / Part: ISL54206A
• Primary Attributes: 2 x SPDT Audio & USB Switch
• Secondary Attributes: 2.7 V ~ 5.5 V Supply
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

To HOST) connector. The BNC connector J9 (COM+) is in
parallel with the audio right line of the headphone jack and
the D+ line of the J1 (USB To DEVICE) connector. These
BNC connectors can be used to connect resistive loads
and/or test equipment to evaluate the performance of the IC.
USB Connections
A “B” type USB receptacle labeled “USB TO HOST” (J1) is
located on the left underside of the board. This receptacle
should be connected (using a standard USB cable) to the
up-stream USB host controller which, is usually a PC
computer or hub. When this connection is made and the IN
logic control is driven HIGH, the ISL54206A device will go
into USB mode. The USB switches will be turned ON.
An “A” type USB receptacle labeled USB TO DEVICE (J2) is
located on the right underside of the board. The USB device
can be plugged directly into this receptacle or through a
standard USB cable.
In USB mode, the USB host controller and the USB device
will be connected through the internal USB switches of the
IC. The USB switches are bi-directional, which allows the
host (computer) and downstream USB device to both send
and receive data.
Note: Before connecting the USB host controller at
connector J1, the headphones must be removed from the
headphone speaker jack, J7. This will prevent the audio load
from interfering with USB signal transmission.
purpose of the ISL54206A device is to allow the use of a
common USB and Audio Headphone Connector in Personal
Media Players and other portable battery powered
equipment. Either a headphone will be in the common
connector to play music or a USB cable from a computer will
be in the common connector to transmit digital data, such as
music, into the memory of the Media Player.
3
The main
Application Note 1337
The BNC connector J8 (COM-) is in parallel with the D- line
of the J1 USB connector. The BNC connector J9 (COM+) is
in parallel with the D+ line of the J1 USB connector.
The BNC connector J14 (D-) is in parallel with the D- line of
the J2 USB connector. The BNC connector J15 (D+) is in
parallel with the D+ line of the J2 USB connector. If you want
to use the J14 and J15 BNC connectors, you must populate
R
used to connect test equipment to evaluate the performance
of the IC.
Board Component Definitions
DESIGNATOR
1
and R
JP1, JP2
J3, J5
J4, J6
JP3
JP4
J10
J11
J12
J13
J14
J15
U1
J1
J2
J7
J8
J9
2
with 0Ω resistors. These BNC connectors can be
ISL54206AIRUZ IC
“B” type USB Receptacle
“A” type USB Receptacle
Left Stereo Audio Input
Right Stereo Audio Input
Headphone Speaker Jack
COM- BNC Connector
COM+ BNC Connector
VDD Positive Connection
VDD Negative Connection
CTRL Logic Control
IN Logic Control
D- BNC Connector
D+ BNC Connector
D-/D+ Differential Probe Connection
IN Pin Connector Selection
Jumper Position 2 to 3 Control through J13
Jumper Position 2 to 1 Control through J1
Connect 4MΩ Pull-down Resistor to IN Pin
DESCRIPTION
July 31, 2007
AN1337.0