MAX1241EVKIT Maxim Integrated Products, MAX1241EVKIT Datasheet
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1241EVKIT
Specifications of MAX1241EVKIT
Related parts for MAX1241EVKIT
MAX1241EVKIT Summary of contents
Page 1
... Convenient On-Board Test Points Data-Logging Software Source Code Provided Fully Assembled and Tested _______________Ordering Information PART TEMP. RANGE MAX1241EVKIT-DIP 0°C to +70°C MAX1241EVL11-DIP 0°C to +70°C MAX1241 EV System _________________________Quick Start The MAX1241 EV kit is fully assembled and tested. Follow these steps to verify board operation. Do not turn on the power supply until all connections are completed ...
Page 2
MAX1241 Evaluation System/Evaluation Kit 5) Connect a cable from the computer’s serial port to the µC module. If using a 9-pin serial port, use a straight-through, 9-pin, female-to-male cable. If the only available serial port uses a 25-pin connector, a ...
Page 3
MAX1241 Evaluation System/Evaluation Kit Table 2. Command Reference KEY FUNCTION C Display the input codes in decimal format. Delay between samples. Delays longer than one second are handled by the IBM PC; otherwise, D the µC module handles the delay. ...
Page 4
MAX1241 Evaluation System/Evaluation Kit TO 68L11D MODULE GND J1-1 GND J1-2 GND J1-3 GND J1-4 VDD VDD J1-7 VDD J1-8 SCLK PA1/IN2 J1-28 PA3/SHDN PA3/IN4/OUT5 J1-30 CS PA6/OUT2 J1-33 DOUT PA7/PAL/OUT1 J1-34 DOUT MISO J1-35 SCLK SCK J1-37 CS J1-38 ...
Page 5
MAX1241 Evaluation System/Evaluation Kit Figure 2. MAX1241 EV Kit Component Placement Guide _______________________________________________________________________________________ 1.0" 5 ...
Page 6
MAX1241 Evaluation System/Evaluation Kit Figure 3. MAX1241 EV Kit PC Board Layout—Component Side 6 _______________________________________________________________________________________ 1.0" ...
Page 7
MAX1241 Evaluation System/Evaluation Kit Figure 4. MAX1241 EV Kit PC Board Layout—Solder Side _______________________________________________________________________________________ 1.0" 7 ...
Page 8
MAX1241 Evaluation System/Evaluation Kit 8 _______________________________________________________________________________________ NOTES ...
Page 9
... DD 6) Turn the power switch off and connect the µC board to an appropriate Maxim EV kit board. ________________________________________________________________ Maxim Integrated Products For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. ____________________Component List ...
Page 10
Module _______________Detailed Description Power Requirements The 68L11D module draws its power from a user-supplied power source connected to terminal block J2. Note the positive and negative markings on the board. Nominal input voltages should be between +5V and +16V. ...
Page 11
Table 2. 40-Pin Data-Connector Signals PIN NAME 1–4 GND Ground 5, 6 V++ Unregulated input voltage V from on-board MAX667 regulator 9 Read strobe Write strobe 11 CS0 Chip select for 8000-8FFF ...
Page 12
Module VDD C13 C12 0.1 F 0 C1- 4 C2+ MAX3232 5 C2 TXD RXD 9 R2 GND 15 POWER CONNECTIONS GND VDD C17 0.1µF ...
Page 13
U9A 74HC139 A14 A15 GND VDD U9B C5 74HC139 0.1µ A12 A13 IOBUFFER 1 R R/W VDD 5 ...
Page 14
Module VDD R5 200 LED1 19 IOBUFFER DIR RD 74HCT245 ...
Page 15
Figure 2. 68L11D Module Component Placement Guide Figure 3. 68L11D Module PC Board Layout—Component Side _______________________________________________________________________________________ 68L11D Module 7 ...
Page 16
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 1997 Maxim Integrated Products Printed USA ...