MAX1241EVKIT Maxim Integrated Products, MAX1241EVKIT Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX1241EVKIT
Manufacturer Part Number
MAX1241EVKIT
Description
EVALUATION KIT FOR MAX1241
Manufacturer
Maxim Integrated Products
Specifications of MAX1241EVKIT
Number Of Adc's
1
Number Of Bits
12
Sampling Rate (per Second)
73k
Data Interface
Serial
Inputs Per Adc
1 Single Ended
Input Range
0 ~ VREF
Power (typ) @ Conditions
3mW @ 73kSPS
Voltage Supply Source
Single Supply
Operating Temperature
0°C ~ 70°C
Utilized Ic / Part
MAX1240, MAX1241
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
The 68L11D module is an assembled and tested PC
board intended for use with Maxim’s low-voltage data-
acquisition evaluation kits (EV kits). The module uses
Motorola’s MC68L11D0FN2 microcontroller (µC) to col-
lect data samples using the SPI interface. It requires an
IBM PC computer and an external DC power supply of
+5V to +16V, or as specified in the appropriate EV kit
manual.
Maxim’s 68L11D module allows customers to evaluate
selected Maxim products. It is not intended to be a
microprocessor development platform, and Maxim
does not support such use.
All system components are guaranteed by their various
manufacturers over the +3V to +3.6V power-supply
range. Not all system components are guaranteed over
the entire 2.5V to 5V V
range. Verify correct operation using the following
procedures:
1) Connect a +5V DC power source (16V max) to the
2) Connect a cable from the computer’s serial port to
3) Start the evaluation kit software on the IBM PC.
4) Adjust trim potentiometer R2 for the desired V
5) To verify correct system operation, press the ESC
6) Turn the power switch off and connect the µC board
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 408-737-7600 ext. 3468.
____________________Getting Started
_______________General Description
µC module at the terminal block located next to the
on/off switch, in the upper-right corner of the µC
module. Turn the power switch on.
the µC module. If using a 9-pin serial port, use a
straight-through, 9-pin, female-to-male cable. If the
only available serial port uses a 25-pin connector, a
standard 25-pin to 9-pin adapter is required.
When the program asks which port the µC module is
connected to, press the space bar until the correct
port is highlighted, and then press ENTER. The soft-
ware will be in terminal-emulation mode. (If using a
generic terminal-emulation program instead of
Maxim EV kit software, select 1200 baud, eight-bit
character, no parity, one stop bit. Send a space
character to start the monitor program.)
supply voltage. Measure V
TP1 and ground. The mounting hole next to R2 is
grounded.
key, type a capital “T”, and then select the count-
down memory test. If the memory test fails or any
other malfunction is reported, the V
low; increase V
to an appropriate Maxim EV kit board.
________________________________________________________________ Maxim Integrated Products
DD
and repeat from step 4.
DD
power-supply adjustment
DD
between test point
DD
voltage is too
DD
____________________Component List
DESIGNATION
C10, C11
JU1, JU2
C12–C18
C1, C2
C4–C9,
LED1
SW1
SW2
U10
U10
C3
D1
R1
R2
R3
R4
R5
R6
U1
U2
U3
U4
U5
U6
U7
U8
U9
Y1
J1
J2
J3
QTY
13
2
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
68L11D Module
22pF ceramic capacitors
0.01µF ceramic capacitor
0.1µF ceramic capacitors
22µF, 20V tantalum capacitors
1N4001 diode
40-pin, right-angle header
2-circuit terminal block
DB9 right-angle socket
Open
Light-emitting diode
10MΩ, 5% resistor
100kΩ potentiometer
274kΩ, 1% resistor
133kΩ, 1% resistor
200Ω, 5% resistor
10kΩ SIP resistor pack, pin 1 common
Slide switch
Momentary push-button switch
Motorola MC68L11D0FN2
Maxim MAX3232CSE
74HC00
Maxim MAX667CSA
32k x 8 static RAM 28-pin socket
Motorola MCM6306DJ15
28-pin socket
74HCT245
Maxim MAX708RCSA
74HC573
74HC139
3V, 8k x 8 ROM
8MHz crystal
DESCRIPTION
1