MAX110EVC32-DIP Maxim Integrated Products, MAX110EVC32-DIP Datasheet
MAX110EVC32-DIP
Specifications of MAX110EVC32-DIP
Related parts for MAX110EVC32-DIP
MAX110EVC32-DIP Summary of contents
Page 1
... Complete Evaluation System ♦ Convenient Test Points Provided On-Board ♦ Data Logging Software ♦ Source Code Provided ♦ User-Selectable Resolution and Speed ______________Ordering Information PART TEMP. RANGE MAX110EVC32-DIP 0°C to +70°C MAX110EVKIT-DIP 0°C to +70°C 80C32MODULE-DIP 0°C to +70°C MAX110EV KIT BOARD TYPE ...
Page 2
MAX110 Evaluation System/Evaluation Kit ________EV System Component List QTY DESCRIPTION 1 MAX110 evaluation kit (MAX110EVKIT-DIP) 1 80C32 µC module (80C32MODULE-DIP) ____________EV Kit Component List DESIGNATION QTY DESCRIPTION C1–C5, C7–10 9 0.1µF ceramic capacitors C11–C15 5 10µF, 16V radial tantalum capacitors ...
Page 3
MAX110 Evaluation System/Evaluation Kit bottom half of each bar graph shows a rolling aver- age of the readings for that channel. The AUTO NULL switch is highlighted. With AUTO NULL and GAIN CAL both off, the bar graphs read the ...
Page 4
MAX110 Evaluation System/Evaluation Kit Be sure to observe frequency and amplitude limits for the MAX110. The recommended frequency of operation is 512kHz for XCLK÷1 mode, 1024kHz for XCLK÷2 mode, or 2048kHz for XCLK÷4 mode. The conversion clock must have a ...
Page 5
MAX110 Evaluation System/Evaluation Kit 1) To monitor the MAX110 supply current, install a cur- rent meter before applying power to the MAX110 EV kit. Refer to the Measuring Supply Current section. Typical supply current is less than 1mA during nor- ...
Page 6
MAX110 Evaluation System/Evaluation Kit Table 3. Command-Line Options OPTION FUNCTION Display program version and list of command- ? line options. Specify the reference voltage ("-V2.5" means 2.5 -V volts). Specify the size of the rolling average queue -A ("-A10" means ...
Page 7
MAX110 Evaluation System/Evaluation Kit The MAX110 Bit Manipulation Panel screen offers direct control of the configuration word and gives a direct view of the output data word. Note that certain bits of the control word are used for factory testing ...
Page 8
MAX110 Evaluation System/Evaluation Kit Table 10. Data-Connector Interface PIN No. 80C32 1–4 GND 7, 8 +5V 27 P1.0 28 P1.1 29 P1.2 30 P1.3 31 P1.4 Complete source code for both MAX110.EXE and 110CODE.MAX is provided on disk. MAX110.EXE was ...
Page 9
MAX110 Evaluation System/Evaluation Kit Listing 1. Sample Code to Read and Write to the MAX110 _______________________________________________________________________________________ 9 ...
Page 10
MAX110 Evaluation System/Evaluation Kit CS DIN SCK POL OFL D13 D12 DOUT BUSY Figure 1. MAX110 EV Kit Timing Diagram 17.33µs 4.35µs SCK DATA VALID DIN 1.14µs SETUP Figure 2. MAX110 EV Kit Detailed Timing Diagram 10 ...
Page 11
MAX110 Evaluation System/Evaluation Kit +5V R8 100Ω MAX873 2 R10 C13 2.43kΩ 10µ C11 10µF R9 200Ω 0.1µF R11 10kΩ R12 1% 100kΩ OPTIONAL +5V R6 100Ω + 0.1µF ...
Page 12
MAX110 Evaluation System/Evaluation Kit Figure 4. MAX110 EV Kit Component Placement Guide— component side Figure 5. MAX110 EV Kit PC Board Layout—Component Side 12 ______________________________________________________________________________________ Figure 6. MAX110 EV Kit PC Board Layout—Solder Side ...
Page 13
MAX110 Evaluation System/Evaluation Kit ____80C32 Module Component List DESIGNATION QTY DESCRIPTION C1 15pF ceramic capacitors C4, C5, C6, C7, C8, C9, C10, 9 0.1µF, 50V ceramic capacitors C11, C12 22µF, 16V radial electrolytic C3, C13, C14 3 capacitors ...
Page 14
MAX110 Evaluation System/Evaluation Kit The port 3 pins (10–17) provide several unrelated functions. Pins 10 and 11 are used as the receive data (RxD) and transmit data (TxD) pins of the RS-232 link. Pins 16 and 17 act as the ...
Page 15
MAX110 Evaluation System/Evaluation Kit Figure 7. 80C32 Module Component Placement Guide (2x) Immediately following transmission of the logon banner, the program runs a checker routine for the on-board 256kbit static RAM. The RAM is filled with several pat- terns and ...
Page 16
MAX110 Evaluation System/Evaluation Kit ALL D9 MNEMONICS REFER TO THE HOST (DTE) 5 GND 1 DCD 4 DTR MAX233A 6 DSR U2 + TXD OUT OUT ...
Page 17
MAX110 Evaluation System/Evaluation Kit 62256 A10 11 23 ...
Page 18
MAX110 Evaluation System/Evaluation Kit Figure 9. 80C32 Module Component-Side Layout (2x) 18 ______________________________________________________________________________________ ...
Page 19
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19 © 1995 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc ...