MAX1181EVKIT Maxim Integrated Products, MAX1181EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX1181EVKIT
• Description: EVAL KIT FOR MAX1181
• Manufacturer: Maxim Integrated Products

Specifications of MAX1181EVKIT

• Number Of Adc's: 1
• Number Of Bits: 10
• Sampling Rate (per Second): 80M
• Data Interface: Parallel
• Inputs Per Adc: 2 Differential
• Input Range: 2 Vpp
• Power (typ) @ Conditions: 246W @ 80MSPS
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: MAX1180, 1181, 1182, 1183, 1184, 1185, 1186, 1190
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Required equipment:
•
•
•
MAX1181 Evaluation Kit
2
DESIGNATION
S/E_INB, D/E_
R9, R10, R13,
INB, CLOCK
DC power supplies
Function generator with low-phase noise and low-
jitter for clock input (e.g., HP8662A)
Function generators for analog signal inputs (e.g.,
HP8662A)
_______________________________________________________________________________________
R14, R36
R12, R37
D/E_INA,
JU1–JU8
S/E_INA,
U3, U4
T1, T2
L1, L2
None
None
None
None
R11
R20
R34
U1
U2
Digital 2.0V, 100mA
Analog 3.0V, 300mA
J1
Component List (continued)
QTY
5
1
2
1
1
2
1
1
2
2
1
5
8
8
1
1
1
2kΩ ±1% resistors (0603)
6.04kΩ ±1% resistor (0603)
4.02kΩ ±1% resistors (0603)
10kΩ ±1% resistor (0603)
5kΩ p otenti om eter , 12- tur n, 1/4”
BI Technologies 3266W-1-502
RF transformers
Mini-Circuits TT1-6-KK81
MAX1181ECM (48-pin TQFP-EP)
receiver (8-pin SO)
Maxim MAX9113ESA
(48-pin TSSOP)
SN74ALVCH16244DGG
100MHz (1206), Fair-Rite
Products Corp.
2512069007Y0 or Mouser
436-2600 (60Ω at 100MHz)
Dual CMOS differential line
Buffer/Driver three-state outputs
Texas Instrument
Ferrite chip beads, 90Ω at
2 x 25-pin header
SMA PC-mount connectors
3-pin headers
Shunt (JU1-JU8)
MAX1181 PC board
MAX1181 data sheet
MAX1181 EV kit data sheet
DESCRIPTION
Quick Start
•
•
•
The MAX1181 EV kit is a fully assembled and tested
surface-mount board. Follow the steps below for board
operation. Do not turn on power supplies or enable
function generators until all connections are
complete.
1) Verify that shunts are installed across pins 2 and 3
2) Connect the clock function generator to the CLOCK
3) Connect the output of the analog signal function
4) a) To evaluate differential analog signals on Channel
Note:
contacting these component suppliers.
AVX
Fair-Rite Products
Kemet
Mini-Circuits
Pericom
Taiyo Yuden
TDK
Texas Instruments
Logic analyzer or data-acquisition system (e.g.,
HP16500C with HP16517A High-Speed Logic State
Card)
Analog bandpass filters (e.g., TTE Elliptical Bandpass
Filter Q56 series)
Digital voltmeter
of jumpers JU5 (offset binary digital output), JU6
(normal operation), JU7 (MAX1181 operating), and
JU8 (outputs enabled).
SMA connector.
generator to the input of the bandpass filter.
A, verify that shunts are installed on pins 2 and 3 of
jumpers JU1 and JU2. Connect the output of the ana-
log bandpass filter to the D/E_INA SMA connector.
For single-ended analog signal evaluation on Channel
A, verify that shunts are installed on pins 1 and 2 of
jumpers JU1 and JU2, and connect the output of the
bandpass filter to the S/E_INA SMA connector.
b) To evaluate differential analog signals on Channel
B, verify that shunts are installed on pins 2 and 3 of
jumpers JU3 and JU4. Connect the output of the ana-
log bandpass filter to the D/E_INB SMA connector.
For single-ended analog signal evaluation on Channel
B, verify that shunts are installed on pins 1 and 2 of
jumper JU3 and JU4, and connect the output of the
bandpass filter to the S/E_INB SMA connector.
SUPPLIER
Please indicate that you are using the MAX1181 when
Component Suppliers
843-448-9411
888-324-7748
864-963-6300
718-934-4500
800-435-2336
800-348-2496
847-803-6100
972-644-5580
PHONE
843-448-1943
888-337-7483
864-963-6322
718-934-7092
408-435-1100
847-952-0899
847-803-6296
214-480-7800
FAX