STEVAL-CBL005V1 STMicroelectronics, STEVAL-CBL005V1 Datasheet - Page 9

• Manufacturer Part Number: STEVAL-CBL005V1
• Description: DEMO BOARD BASED ON LNBH23
• Manufacturer: STMicroelectronics
• Type: DC/DC Switching Converters, Regulators & Controllersr

Specifications of STEVAL-CBL005V1

• Main Purpose: Special Purpose DC/DC, LNB
• Outputs And Type: 1, Non-Isolated
• Voltage - Input: 8 ~ 15V
• Regulator Topology: Boost
• Board Type: Fully Populated
• Utilized Ic / Part: LNBH23
• Input Voltage: 8 V to 15 V
• Interface Type: I2C
• Product: Power Management Modules
• Silicon Manufacturer: ST Micro
• Silicon Core Number: LNBH23
• Kit Application Type: Power Management
• Application Sub Type: LNB Power Supply
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Voltage - Output: -
• Power - Output: -
• Frequency - Switching: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: LNBH23
• Other names: 497-8717

LNBH23
3
Figure 3.
Table 2.
Pin n° for
QFN32
19
18
27
21
22
12
14
29
4
6
9
DSQOUT
DSQOUT
VCTRL
VCTRL
P-GND
P-GND
DSQIN
DSQIN
DETIN
DETIN
ADDR
ADDR
Pin n° for
SDA
SDA
SCL
SCL
PSSO-24
NC
NC
NC
NC
NC
NC
LX
LX
Pin description
Pin configuration
Pin connections (top view for PowerSSO-24, bottom view for QFN32)
17
16
22
19
20
12
14
6
8
9
1
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
PowerSSO-24
Symbol
DSQIN
DETIN
V
V
V
SDA
SCL
TTX
V
V
CC–L
LX
oRX
oTX
CC
UP
Output port for 22
Step-Up voltage
LDO output port
Tone decoder
DiSEqC input
N-MOS drain
Supply input
Supply input
kHz tone TX
Serial clock
TTX enable
Serial data
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
Name
input
NC
NC
ISEL
ISEL
VUP
VUP
NC
NC
VoTX
VoTX
VoRX
VoRX
A-GND
A-GND
VCC
VCC
BYP
BYP
TTX
TTX
EXTM
EXTM
VCC-L
VCC-L
Doc ID 13356 Rev 7
8 to 15 V analog power supply.
8 to 15 V IC DC-DC power supply.
Integrated N-Channel power MOSFET drain.
Input of the linear post-regulator. The voltage on this pin is
monitored by the internal step-up controller to keep a
minimum dropout across the linear pass transistor.
Output of the integrated low drop linear post-regulator. See
truth tables for voltage selections and description.
TX Output to the LNB. See truth tables for selection.
Bi-directional data from/to I²C bus.
Clock from I²C bus.
This pin will accept the DiSEqC code from the main
microcontroller. The LNBH23 will use this code to modulate
the internally generated 22 kHz carrier. Set to ground if not
used.
This pin can be used, as well as the TTX I²C bit of the system
register, to control the TTX function enable before to start the
22 kHz tone transmission. Set floating or to GND if not used.
22 kHz tone decoder Input, must be AC coupled to the
DiSEqC 2.0 bus.
QFN32 (5 x 5 mm.)
Function
Pin configuration
9/32