ISL6228HIEVAL3Z Intersil, ISL6228HIEVAL3Z Datasheet - Page 6

• Manufacturer Part Number: ISL6228HIEVAL3Z
• Description: EVALUATION BOARD FOR ISL6228HI
• Manufacturer: Intersil
• Series: Robust Ripple Regulator™ (R³)r

Specifications of ISL6228HIEVAL3Z

• Main Purpose: DC/DC, Step Down
• Outputs And Type: 2, Non-Isolated
• Voltage - Output: 1.05V or 1.2V, 1.2V
• Current - Output: 20A, 20A
• Voltage - Input: 3.3 ~ 25V
• Regulator Topology: Buck
• Frequency - Switching: 270kHz, 300kHz
• Board Type: Fully Populated
• Utilized Ic / Part: ISL6228
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Power - Output: -

Electrical Specifications
Functional Pin Descriptions
GND (Bottom Pad)
Signal common of the IC. Unless otherwise stated, signals
are referenced to the GND pin.
FSET2 (Pin 1)
The FSET2 pin programs the PWM switching frequency of
Channel 2. Program the desired PWM frequency with a
resistor and a capacitor connected across the FSET2 and
GND pins.
VIN2 (Pin 2)
The VIN2 pin measures the input voltage of the Channel 2
converter. It is a required input to the Channel 2 R
modulator. Connect the VIN2 pin to the drain of the
Channel 2 high-side MOSFET.
VCC2 (Pin 3)
The VCC2 pin is the input bias voltage for Channel 2.
Connect +5V to the VCC2 pin. Decouple with at least 1µF of
a MLCC capacitor from the VCC2 pin to the GND pin.
VCC1 (Pin 4)
The VCC1 pin is the input bias voltage for Channel 1.
Connect +5V to the VCC1 pin. Decouple with at least 1µF of
a MLCC capacitor from the VCC1 pin to the GND pin.
VIN1 (Pin 5)
The VIN1 pin measures the input voltage of the Channel 1
converter. It is a required input to the Channel 1 R
modulator. Connect the VIN1 pin to the drain of the
Channel 1 high-side MOSFET.
FSET1 (Pin 6)
The FSET1 pin programs the PWM switching frequency of
Channel 1. Program the desired PWM frequency with a
resistor and a capacitor connected across the FSET1 and
GND pins.
PGOOD1 (Pin 7)
The PGOOD1 pin is an open-drain output that indicates
when the Channel 1 converter is able to supply regulated
voltage. Connect the PGOOD1 pin to +5V through a pull-up
resistor.
FB1 (Pin 8)
The FB1 pin is the inverting input of the control-loop error
amplifier for Channel 1. The Channel 1 converter output
voltage regulates to 600mV from the FB1 pin to the GND pin.
Program the desired output voltage with a resistor network
OTP Rising Threshold (Note 3)
OTP Hysteresis (Note 3)
PARAMETER
6
These specifications apply for T
PVCC = 5V; Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified.
Temperature limits established by characterization and are not production tested. (Continued)
SYMBOL
T
T
OTHYS
OTR
3
3
PWM
PWM
ISL6228
A
= -40°C to +100°C; All typical specifications T
TEST CONDITIONS
connected across the VO1, FB1, and GND pins. Select the
resistor values such that FB1 to GND is 600mV when the
converter output voltage is at the programmed regulation
value.
VO1 (Pin 9)
The VO1 pin measures the Channel 1 converter output
voltage and is used as an input to the Channel 1 R
modulator. It also serves as part of Channel 1 inductor
current sensing and the OCP overcurrent fault protection
circuit.
OCSET1 (Pin 10)
The OCSET1 pin measures the Channel 1 inductor current
and programs the threshold of the OCP overcurrent fault
protection.
EN1 (Pin 11)
The EN1 pin is the on/off switch of Channel 1. The soft-start
sequence begins when the EN1 pin is pulled above the
rising threshold voltage V
power-on reset (POR) rising threshold voltage
When the EN1 pin is pulled below the falling threshold
voltage V
PHASE1 (Pin 12)
The PHASE1 pin is the current return path for the Channel 1
high-side MOSFET gate driver. Connect the PHASE1 pin to
the node consisting of the high-side MOSFET source, the
low-side MOSFET drain, and the output inductor of the
Channel 1 converter.
UGATE1 (Pin 13)
The UGATE1 pin is the output of the Channel 1 high-side
MOSFET gate driver. Connect the UGATE1 pin to the gate
of the Channel 1 converter high-side MOSFET.
BOOT1 (Pin 14)
The BOOT1 pin stores the input voltage for the Channel 1
high-side MOSFET gate driver. Connect an MLCC capacitor
across the BOOT1 and PHASE1 pins. The boot capacitor is
charged through an internal boot diode connected from the
PVCC1 pin to the BOOT1 pin, each time the PHASE1 pin
drops below PVCC1 minus the voltage dropped across the
internal boot diode.
PVCC1 (Pin 15)
The PVCC1 pin is the input voltage bias for the Channel 1
low-side MOSFET gate drivers. Connect +5V to the PVCC1
ENTHF
PWM1 immediately stops.
ENTHR
MIN
A
and VCC1 is above the
-
-
= +25°C, VCC = 5V,
TYP
150
25
V VCC_THR
MAX
-
-
3
May 7, 2008
PWM
FN9095.2
UNIT
°C
°C
.