ISL5861EVAL1 Intersil, ISL5861EVAL1 Datasheet - Page 3

• Manufacturer Part Number: ISL5861EVAL1
• Description: EVALUATION PLATFORM ISL5861 SOIC
• Manufacturer: Intersil
• Series: CommLink™r

Specifications of ISL5861EVAL1

• Number Of Dac's: 1
• Number Of Bits: 12
• Outputs And Type: 1, Differential
• Sampling Rate (per Second): 210M
• Data Interface: Parallel
• Dac Type: Current
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: ISL5861 SOIC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

generate 1-4 narrowband carriers or 1-2 wideband carriers.
Consult the ISL5217 documentation for detailed information
on using the ISL5217 evaluation board.
To connect the two boards together, J4 on the ISL5217eval
(DUC) is connected to J1 on the ISL5x61eval (DAC) via a
2x20 pin ribbon cable. The DAC board is configured as is
stocked, except R16 is not populated. See Figure 2 for a
block diagram of the two boards connected.
If a clock source is available that has both CLK and CLK, the
clocking of the two boards is simplified. CLK should connect
to the DUC evaluation board at J11, with a T-connector that
has a 50Ω terminator attached. CLK should go to the DAC
evaluation board at J2 and also use a T-connector with a
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice.
Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable.
However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its
use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
7585 Irvine Center Drive
Suite 100
Irvine, CA 92618
TEL: [phone]
FAX: [phone]
ISL5217 EVALUATION BOARD
All Intersil products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
UP CONVERTER
For information regarding Intersil Corporation and its products, see www.intersil.com
4CH DIGITAL
ISL5217
CLOCK (104M MAX)
3
Intersil Corporation
2401 Palm Bay Rd.
Palm Bay, FL 32905
TEL: [phone]
FAX: [phone]
FIGURE 2. INTERSIL ISL5x61 + ISL5217 SETUP BLOCK DIAGRAM
Application Note 9966
+5V (<2A)
RIBBON CABLE
SUPPLY
POWER
EUROPE
Intersil Europe Sarl
Ave. C - F Ramuz 43
CH-1009 Pully
Switzerland
TEL: [phone]
FAX: [phone]
50Ω terminator. (Or, 50Ω terminators can be populated on
the evaluation boards. See the board schematics for more
information on doing this.)
If a generator with CLK and CLK is not available, a single
clock source can be used. Connect a T-connector to J2 of
the DAC board and another to J11 of the DUC board.
Connect a DC-biased clock signal to the connector at J2,
then connect J2 and J11 together with a short cable.
Connect a 50Ω terminator to the other side of the
T-connector at J11 on the DUC board. Sometimes the length
of the clock cable running from the DAC board to the DUC
board has to be adjusted to achieve adequate setup and
hold times between DATA and CLK.
ISL5x61 EVALUATION BOARD
14 BITS
CLOCK (104M MAX)
SUPPLY
POWER
ISL5x61
ASIA
Intersil Corporation
Unit 1804 18/F Guangdong Water Building
83 Austin Road
TST, Kowloon Hong Kong
TEL: [phone]
FAX: [phone]
DAC
+3.3V (<0.1A)
TO SPECTRUM
CABLE
50Ω
SMA
ANALYZER