HI5728EVAL1 Intersil, HI5728EVAL1 Datasheet - Page 2

• Manufacturer Part Number: HI5728EVAL1
• Description: EVALUATION PLATFORM TQFPHI5728
• Manufacturer: Intersil

Specifications of HI5728EVAL1

• Number Of Dac's: 2
• Number Of Bits: 10
• Outputs And Type: 2, Differential
• Sampling Rate (per Second): 125M
• Data Interface: Parallel
• Settling Time: 35ns
• Dac Type: Current
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: HI5728
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Functional Description
Overview
The evaluation board is configured to be interfaced using a
VME connector. The data input lines are tied together using
small, zero ohm resistors on the back side of the board (QD0
is tied to ID0, continued with QD9 connected to ID9; see the
schematic, R54, 58-60, 62-67). This is done so that the data
can be driven into both of the channels without having to
generate two patterns. This aids in simplifying the evaluation
of the part. If the user has the ability to generate dual
patterns during the evaluation process, these resistors must
be removed. Both series and parallel termination resistor
footprints are provided, so that the user may customize the
termination method. An internal voltage reference is
available, as well as a variable resistor for customizing the
output current. RF transformers are populated for taking
advantage of the complimentary current outputs. They can
be disabled from the circuit by removing several zero ohm
resistors if a simple load resistor output is desired.
Voltage Reference
The HI5728 has an internal voltage reference (1.16V typical)
with a 60ppm/
range of the converter. The REFLO pin (15) selects the
reference. Access to pin 15 is provided through the center
pin of Jumper J2. To enable the internal reference, it is
necessary that the jumper be placed such that pin 15 is
grounded (J2 is labeled on the board as INT and EXT, for
internal and external). The REFIO pin (23) provides access
to the internal voltage reference, or can be overdriven if the
user wishes to use an external source for the reference.
Notice that a 0.1 F capacitor is placed as close as possible
to the REFIO pin. This capacitor is necessary for ensuring a
quiet reference voltage.
If the user wishes to use an external reference voltage,
jumper J3 must be in place and an external voltage
reference provided via SMA7, labeled ‘EXT REF’. Jumper J2
must be changed so that pin 16 is tied high (the supply
voltage, which is the EXT position of J2) when using an
external reference. The recommended limits of the external
reference are between 15mV and 1.2V, which provides over
36dB of multiplying capability. Performance of the converter
can be expected to decline as the reference voltage is
reduced due to the reduction in LSB current size.
If the user wishes to amplitude modulate the reference, the
REFIO pin can be overdriven with a waveform. The input
multiplying bandwidth of the REFIO input is approximately
1.4MHz. It is necessary that the multiplying signal be DC
offset so that the minimum and maximum peaks of the signal
are above 0V and less than 1.2V. The output current of each
converter is a function of the voltage reference used and the
value of R
potentiometer that can be used to vary the R
wishes to explore various output current levels. The board is
SET
(R68 or R35 on the schematic). R68 is a
o
C drift coefficient over the full temperature
3-2
SET
Application Note 9827
if the user
shipped with R68 set to ~2k . The converter’s performance
sometimes improves with reduced output current. R35 is
provided if the user wishes to set the output current using a
set value. See the ‘Outputs’ section for more information on
setting the output current.
The footprints for SMA10 and SMA11 were provided on the
evaluation board so that separate multiplying signals could
be attached, along with alternate op amps, to overdrive the
internal reference op amps via ICOMP1 and QCOMP1 to
increase the multiplying bandwidth of the references for
DACs I and Q independently. SMA11 was placed next to
prototyping area so that an external op amp could be placed
between E11 and E7, which provides access to QCOMP1
via a zero ohm resistor, R69. It was intended that this
capability also exist between E10 and E6 for access to
ICOMP1 so that it could be driven independently if desired,
but E6 was mistakenly grounded. So the ability to overdrive
ICOMP1 and QCOMP1 exists on this board, but it must be
done with a single op amp and signal simultaneously via
SMA11, E7, and E11. ICOMP1 cannot be driven
independently using SMA10, E6, and E10. R56 should never
be populated. See the functional block diagram of the
HI5728 in the data sheet and the evaluation board schematic
located in this document for more information.
Outputs
The output current of the device is set by choosing R
and V
is less than 20mA:
I
For example, using the internal V
and an R
in an I
Choose the output loading so that the ‘Output Voltage
Compliance Range’ is not violated (-0.3 to 1.25V). If an
external V
The output can be configured to drive a load resistor, a
transformer, an operational amplifier, or any other type of
output configuration so long as the output voltage
compliance range and the maximum output current is not
violated.
Load Resistor Output
If the user wishes to use only a load resistor and no
transformer, they should remove the zero ohm resistors that
connect the outputs to the transformers. These resistors are
R51, R57, R70, and R72. See the schematic for details. The
output voltage developed is simply a function of the output
current multiplied by the output load. Care should be taken
to ensure that this voltage does not violate the output
compliance range of -300mV to 1.25V.
OUT
= 32 x V
FSADJ
OUT
SET
REF
of approximately 20mA (maximum allowed).
such that the resultant of the following equation
(R35 on the schematic) value of 1.86k results
FSADJ
is chosen, it should not exceed +1.2V.
/R
SET
.
FSADJ
of 1.16V nominal
SET