NCP5602EVB ON Semiconductor, NCP5602EVB Datasheet

NCP5602EVB

Manufacturer Part Number

NCP5602EVB

Description

EVAL BOARD FOR NCP5602

Manufacturer

ON Semiconductor

Datasheets

1.NCP5602MUTBG.pdf (12 pages)

2.NCP5602EVB.pdf (2 pages)

Specifications of NCP5602EVB

Design Resources

NCP5602 EVB BOM NCP5602EVB Gerber Files NCP5602 EVB Schematic

Current - Output / Channel

60mA

Outputs And Type

2, Non-Isolated

Voltage - Output

4.8 ~ 5.7 V

Features

Dimmable

Voltage - Input

3.6V

Utilized Ic / Part

NCP5602

Core Chip

NCP5602

Topology

Charge Pump

No. Of Outputs

Development Tool Type

Hardware - Eval/Demo Board

Leaded Process Compatible

Yes

Mcu Supported Families

NCP5602

Rohs Compliant

Yes

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

For Use With/related Products

NCP5602

Other names

NCP5602EVBOS

Current page: 1 of 2
Download datasheet (139Kb)

Test Procedure for the NCP5602 Evaluation Board

1/10/2008

Power Supply:

Connect a DC power supply, with 500mA output current capability, across the two pins built

with connector J2. Make sure the polarity is properly respected: reverse polarity will destroy the

NCP5602.

Set up the power supply to 3.6V. Although the supply voltage can be adjusted between 2.85V –

5.5V for engineering purpose, the associated MCU test board is limited to 3.6V; double check

the power supply before to turn ON the supply.

Test Procedure:

1. Connect the IDC10/J1 connector to the external MCU board with the ribbon cable. Double

check the power supply is set up at 3.6V, maximum rating is 3.8V.

2. The MCU board is powered by the same external DC supply once the ribbon cable is attached

on both boards.

3. Turn ON the power supply: LED D1 on the MCU board shall turn ON. Reset the MCU if

necessary by pushing the RESET button S7.

4. Push control button F1: the two LED shall be activated and the brightness can be increased by

pushing the F1 control.

5. Push control button F5: the two LED shall be dimmed toward zero with consecutive pushes on

the F2 command.

6. Push command F3: the ICON mode shall be activated, same as #4. Since bounces are

generated by the manual push buttons, non linear operation can happen during the test. This is

normal and the part shall NOT be rejected for such a reason. The final test is complete when all

the steps #4 to #7 are proven OK. However, it is not necessary to cover all the sixteen steps to

ramp up/ down the brightness: the system is fully debugged if the four tests mentioned above are

successful.

Related parts for NCP5602EVB

NCP5602EVB Summary of contents

Page 1

Test Procedure for the NCP5602 Evaluation Board 1/10/2008 Power Supply: Connect a DC power supply, with 500mA output current capability, across the two pins built with connector J2. Make sure the polarity is properly respected: reverse polarity will destroy the ...

Page 2

Digital Control possible to drive the NCP5602 by means of an external controller, leaving aside the MCU test package. In this case, one shall connect an external I2C system to connector J1 /IDC10. The external controller shall send ...

Related keywords

ncp561
ncp5608
ncp5604a
ncp5604
ncp5603
ncp5602
NCP5602EVB datasheet
NCP5602EVB data sheet
NCP5602EVB pdf datasheet
NCP5602EVB component
NCP5602EVB part
NCP5602EVB distributor
NCP5602EVB RoHS
NCP5602EVB datasheet download