LM3509SDEV National Semiconductor, LM3509SDEV Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LM3509SDEV
Manufacturer Part Number
LM3509SDEV
Description
BOARD EVALUATION FOR LM3509SD
Manufacturer
National Semiconductor
Series
PowerWise®r
Specifications of LM3509SDEV
Current - Output / Channel
40mA
Outputs And Type
2, Non-Isolated
Voltage - Output
21V
Features
Dimmable, I²C Interface
Voltage - Input
2.7 ~ 5.5V
Utilized Ic / Part
LM3509
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
RESET/GPIO Pin Voltage Specifications
V
V
V
I
V
V
V
V
I
t
t
t
t
t
4
2
2
1
2
3
5
IL
IH
OL
C Compatible Voltage Specifications (SCL, SDA, VIO)
IO
IL
IH
OL
C Compatible Timing Specifications (SCL, SDA, VIO, see Figure 1) (Notes 8, 9)
Note 1: Absolute maximum ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions for which the device is intended
to be functional, but device parameter specifications may not be guaranteed. For guaranteed specifications and test conditions, see the Electrical Characteristics.
Note 2: All voltages are with respect to the potential at the GND pin.
Note 3: For detailed soldering specifications and information, please refer to National Semiconductor Application Note 1187: Leadless Lead frame Package
(AN-1187).
Note 4: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at T
T
Note 5: In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may have to be
derated. Maximum ambient temperature (T
dissipation of the device in the application (P
following equation: T
Note 6: Junction-to-ambient thermal resistance (θ
JEDEC standard JESD51-7. The test board is a 4-layer FR-4 board measuring 114mm x 76mm x 1.6mm with a 2x1 array of thermal vias. The ground plane on
the board is 113mm x 75mm. Thickness of copper layers are 71.5µm/35µm/35µm/71.5µm (2oz/1oz/1oz/2oz). Ambient temperature in simulation is 22°C, still air.
Power dissipation is 1W. The value of θ
board material, layout, and environmental conditions. In applications where high maximum power dissipation exists special care must be paid to thermal dissipation
issues. For more information on these topics, please refer to Application Note 1187: Leadless Leadframe Package (LLP) and the Power Efficiency and Power
Dissipation section of this datasheet.
Note 7: Min and Max limits are guaranteed by design, test, or statistical analysis. Typical (Typ) numbers are not guaranteed, but represent the most likely norm.
Note 8: SCL and SDA must be glitch-free in order for proper brightness control to be realized.
Note 9: SCL and SDA signals are referenced to VIO and GND for minimum VIO voltage testing.
Note 10: The human body model is a 100pF capacitor discharged through 1.5kΩ resistor into each pin. (MIL-STD-883 3015.7).
Note 11: The matching specification between MAIN and SUB is calculated as 100 × ((I
100 × (I
J
=140ºC (typ.).
Symbol
MAIN
- I
SUB
)/(I
Input Logic Low
Input Logic High
Output Logic Low
Serial Bus Voltage Level
Input Logic Low
Input Logic High
Output Logic Low
SCL Clock Period
Data In Setup Time to SCL
High
Data Out Stable After SCL
Low
SDA Low Setup Time to
SCL Low (Start)
SDA High Hold Time After
SCL High (Stop)
MAIN
A-MAX
+ I
= T
SUB
J-MAX-OP
Parameter
).
– (θ
JA
JA
of this product in the LLP package could fall in a range as wide as 50ºC/W to 150ºC/W (if not wider), depending on
A-MAX
× P
D-MAX
D-MAX
) is dependent on the maximum operating junction temperature (TJ-MAX-OP = +105ºC), the maximum power
), and the junction-to ambient thermal resistance of the part/package in the application (θ
JA
) is taken from a thermal modeling result, performed under the conditions and guidelines set forth in the
).
2.7V < V
= 0
2.7V < V
= 0
I
2.7V < V
2.7V < V
2.7V < V
I
LOAD
LOAD
=3mA, MODE bit = 1
= 3mA
FIGURE 1. I
Conditions
IN
IN
IN
IN
IN
<5.5V, MODE bit
< 5.5V, MODE bit
< 5.5V (Note 9)
< 5.5V
< 5.5V
5
2
C Timing
MAIN
or I
SUB
0.7×V
) - I
Min
100
100
100
1.1
1.4
2.5
0
AVE
IO
) / I
30004303
AVE
. This simplifies out to be
Typ
J
=150ºC (typ.) and disengages at
0.36×V
Max
400
400
V
0.5
V
IN
IO
JA
IO
), as given by the
www.national.com
Units
mV
mV
µs
ns
ns
ns
ns
V
V
V
V
V