AS1116 DB-BLUE austriamicrosystems, AS1116 DB-BLUE Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/0/84/austriamicrosystems_sml.jpg)
AS1116 DB-BLUE
Manufacturer Part Number
AS1116 DB-BLUE
Description
BOARD DEMO AS1116 BLUE
Manufacturer
austriamicrosystems
Specifications of AS1116 DB-BLUE
Current - Output / Channel
*
Outputs And Type
8, Non-Isolated
Voltage - Output
*
Features
64 LED Driver with Error Detection, SPI
Voltage - Input
2.7 ~ 5.5 V
Utilized Ic / Part
AS1116
Lead Free Status / RoHS Status
Lead free by exemption / RoHS compliant by exemption
AS1116
Datasheet - D e t a i l e d D e s c r i p t i o n
Shutdown Mode
The AS1116 devices feature a shutdown mode, where they consume only 200nA (typ) current. Shutdown mode is
entered via a write to the Shutdown Register (see
and digital drivers are switched off, so that all segments are blanked.
Note: During shutdown mode the Digit-Registers maintain their data.
Shutdown mode can either be used as a means to reduce power consumption or for generating a flashing display
(repeatedly entering and leaving shutdown mode). For minimum supply current in shutdown mode, logic input should
be at GND or V
When entering or leaving shutdown mode, the Feature Register is reset to its default values (all 0s) when Shutdown
Register bit D7 (page 10) = 0.
Note:
Digit- and Control-Registers
The AS1116 devices contain 8 Digit-Registers,11 control-registers and 8 diagnostic-registers, which are listed in
7. All registers are selected using a 8-bit address word, and communication is done via the serial interface.
www.austriamicrosystems.com/LED-Driver-ICs/AS1116
Table 7. Register Address Map
!
!
without rewriting the whole register contents.
down, display test and features selection registers.
Digit Registers – These registers are realized with an on-chip 64-bit memory. Each digit can be controlled directly
Control Registers – These registers consist of decode mode, display intensity, number of scanned digits, shut-
DIG0:DIG1 Intensity
DIG2:DIG3 Intensity
DIG4:DIG5 Intensity
DIG6:DIG7 Intensity
Display Test Mode
Global Intensity
Decode-Mode
When
down mode. If the AS1116 is used with an external clock, Shutdown Register bit D7 should be set to 1 when
writing to the Shutdown Register.
Scan Limit
Shutdown
Not Used
Register
Feature
No-Op
Digit 0
Digit 1
Digit 2
Digit 3
Digit 4
Digit 5
Digit 6
Digit 7
Shutdown Register bit D7 = 1, the Feature Register is left unchanged when entering or leaving shut-
DD
(CMOS logic level).
D15
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
D14 D13 D12
0/1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
Table
D11
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
Revision 1.05
8). For the AS1116, at that point, all segment current sources
D10
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
Address
D9
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
D8
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
(see Table 16 on page
(see Table 18 on page
(see Table 19 on page
(see Table 13 on page
(see
(see Table 17 on page
(see Table 17 on page
(see Table 17 on page
(see Table 17 on page
(see Table 9 on page
(see Table 8 on page
Table 11 on page 11
Table 12 on page
Table 10 on page
D7:D0
11)
and
10)
10)
13)
13)
14)
12)
13)
13)
13)
13)
11,
Page
Table
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
14
10
13
13
14
10
9 - 20
9