ISL28213MSOPEVAL2Z Intersil, ISL28213MSOPEVAL2Z Datasheet - Page 2

• Manufacturer Part Number: ISL28213MSOPEVAL2Z
• Description: EVALUATION BOARD FOR ISL28213
• Manufacturer: Intersil

Specifications of ISL28213MSOPEVAL2Z

• Channels Per Ic: 2 - Dual
• Amplifier Type: General Purpose
• Output Type: Rail-to-Rail
• Slew Rate: 1 V/µs
• Current - Output / Channel: 22mA
• Operating Temperature: -40°C ~ 125°C
• Current - Supply (main Ic): 90µA
• Voltage - Supply, Single/dual (±): 2.4 V ~ 5.5 V, ±1.2 V ~ 2.75 V
• Board Type: Fully Populated
• Utilized Ic / Part: ISL28213
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• -3db Bandwidth: -

User-Selectable Options
(Figures 3 and 4)
Component pads are included to enable a variety of
user-selectable circuits to be added to the amplifier VREF,
inputs, outputs, and the amplifier feedback loops. The
inputs (see Figure 3) have additional resistor, capacitor,
and jumper placements for loading and/or measurement
of frequency sensitive parameters.
ISL28213/14MSOPEVAL2Z Components Parts List
J1
J2
R11, R14, R21, R24, R28,
R4, R16, R25-R27, R31
R13, R18, R19, R23
R30, R32, R34-R36
U1 (ISL28213FUZ)
U1 (ISL28214FUZ)
C1, C6-C10
DEVICE #
C2, C4
C3, C5
R29
D1
DNP
DNP
R1
R2
FIGURE 3. INPUT STAGE (1/2)
CAP-TANTALUM, SMD, 1.0µF, 50V, 10%, LOW ESR, ROHS
CAP, SMD, 0603, 0.1µF, 25V, 10%, X7R, ROHS
CAP, SMD, 0603, DNP-PLACE HOLDER, ROHS
DIODE-SCHOTTKY BARRIER, SMD, SOT-23, 3P, 40V, ROHS
ISL28213FUZ-T7, IC-RAIL-TO-RAIL OP AMP, MSOP, ROHS
ISL28214FUZ-T7, IC-RAIL-TO-RAIL OP AMP, MSOP, ROHS
RESISTOR, SMD, 0603, 0.1%, MF, DNP-PLACE HOLDER
RES, SMD, 0603, 0Ω, 1/10W, TF, ROHS
RES, SMD, 0603, 10k, 1/10W, 1%, TF, ROHS
RES, SMD, 0603, 100k, 1/10W, 1%, TF, ROHS
2
IN-
R4
0
IN+
R15
DNP
10k
R10
DNP
R11
10k
Application Note 1542
NODE
100k
R18
OPEN
100k
R12
DNP
R13
R14
DESCRIPTION
C1
OUT
VREF
TO OUTPUT
TO IN-
TO IN+
The outputs (see Figure 4) have a 10kΩ load resistor to
ground and have additional resistor and capacitor
placements for loading.
NOTE: Operational amplifiers are sensitive to output
capacitance and may oscillate. In the event of oscillation,
reduce output capacitance by using shorter cables, or
add a resistor in series with the output.
FROM OUTPUT
FIGURE 4. OUTPUT STAGE (1/2)
OPEN
R26
C6
Power Supply Decoupling
Power Supply Decoupling
populated
Reverse Power Protection
populated
0Ω User Selectable Resistors
Gain and Other User Selectable
Resistors
Gain Resistors
0
User Selectable Capacitors - not
User Selectable Resistors - not
COMMENTS
February 18, 2010
AN1542.0