TWR-SENSOR-PAK Freescale Semiconductor, TWR-SENSOR-PAK Datasheet

Page 1

... Quick Start Guide for TWR-SENSOR-PAK TWR-SENSOR-PAK Swappable sensor module TOWER SYSTEM ...

Page 2

... TOWER SYSTEM Get to know the TWR-SENSOR-PAK S08JM BDM Header Primary Elevator Connector LEDs Reset Button Infrared Receiver miniB USB (Power, OSBDM, Communication) Temperature/Humidity Sensor Ambient Light Sensor with Proximity Secondary Elevator Connector TWRPI-MMA7660 Accelerometer Plug-in TWRPI-MPL115A Barometer Plug-in Config Jumpers Serial Config ...

Page 3

... Get to know the TWR-SENSOR-PAK MC9S08QE96CLK TWR-SENSOR-PAK Freescale Tower System The TWR-SENSOR-PAK module is part of the Freescale Tower System, a modular development platform that enables rapid prototyping and tool re-use through reconfigurable hardware. Take your design to the next level and begin constructing your Tower System today. ...

Page 4

... TOWER SYSTEM How to assemble the TWR-SENSOR-PAK module STEP Locate the TWR-SENSOR 1 module and the five plug-ins included in the TWR-SENSOR-PAK. • TWRPI-KEYPAD • TWRPI-TSS • TWRPI-MMA7660 • TWRPI-MPL115A • TWRPI-MPR121 STEP Identify the sensor plug-in 2 modules that you plan to use and insert them into the appropriate sockets. ...

Page 5

... Quick Start Guide for TWR-SENSOR-PAK How to assemble the TWR-SENSOR-PAK module TOWER SYSTEM ...

Page 6

... TOWER SYSTEM TWR-SENSOR-PAK features Swappable Freescale Sensor Modules • Touch sense controller (MPR121) • Accelerometer (MMA7660) • Pressure sensor (MPL115A) Keypad Touch Pad Module On-Board Slider/Touch Pad • With dedicated touch sense controller (MPR032) On-Board MCU (MC9S08QE96) • Stand-alone operation • Slave MCU mode • Tower MCU mode (with limited peripheral connectivity) • Touch sense software evaluation On-Board Third-Party Sensors • ...

Page 7

... Quick Start Guide for TWR-SENSOR-PAK How to build your Tower STEP Ensure that the TWR-SENSOR 1 module configuration and isolation jumpers are set for correct communication with the Tower System. Refer to TWR-SENSOR-PAK Jumper Options. STEP Locate the Elevator modules, 2 identifiable by the four card edge connectors on each. ...

Page 8

... TOWER SYSTEM Step-by-step installation instructions In this Quick Start Guide, you will learn how to set up the TWR-SENSOR- PAK module and run the default FreeMASTER demonstration. STEP Install software 1 and tools • Install FreeMASTER Run-Time Debugging Tool from included DVD. • If desired, install CodeWarrior Development Studio for Microcontroller v6.3 from included DVD ...

Page 9

... STEP Interact 5 Interact with the TWR-SENSOR module sensors and view the associated graphs and display gauges within the FreeMASTER application. STEP Explore additional 6 resources Explore the additional documentation and software resources in the included DVD and on the TWR-SENSOR-PAK site at www.freescale.com/tower. TOWER SYSTEM ...

Page 10

... TOWER SYSTEM TWR-SENSOR-PAK Jumper Options The following is a list of all the jumper options. The *default* installed jumper settings are shown in bold with asterisks. Jumper Name J2 BTLD J3 MCU 3V3 J4 ANA EN J5 SERIAL CFG Setting 1-2 Shunt to enable Boot Loader Mode *1-2* Connects 3V3 to MCU. Use to measure MCU current consumption ...

Page 11

... Quick Start Guide for TWR-SENSOR-PAK Jumper Name Setting OSBDM/SER Shunt to enable Sensor I 1-2 Connects SENS_SDA to ELE_SDA1 Shunt to enable MCU I *3-4* Connects MCU_SDA to ELE_SDA0 Shunt to enable Sensor I 5-6 Connects SENS_SCL to ELE_SCL1 Shunt to enable MCU I *7-8* Connects MCU_SCL to ELE_SCL0 Shunt to enable Sensor I 1-3 ...

Page 12

... TOWER SYSTEM TOWER SYSTEM To learn more about the TWR-SENSOR-PAK and other modules within the Tower System, visit www.freescale.com/tower. To become a member of the online Tower Geeks community, visit www.towergeeks.org. Freescale, the Freescale logo and CodeWarrior are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. All other product or service names are the property of their respective owners. ...