AS5046 AB austriamicrosystems, AS5046 AB Datasheet - Page 28
![no-image](/images/manufacturer_photos/0/0/84/austriamicrosystems_sml.jpg)
AS5046 AB
Manufacturer Part Number
AS5046 AB
Description
BOARD ADAPTER AS5046
Manufacturer
austriamicrosystems
Specifications of AS5046 AB
Sensor Type
Magnetic, Rotary Position
Sensing Range
360°
Interface
Serial
Voltage - Supply
9V
Embedded
No
Utilized Ic / Part
AS5046
Lead Free Status / RoHS Status
Lead free by exemption / RoHS compliant by exemption
Sensitivity
-
AS5046
Data Sheet
Figure 17
15.2.1 Angular Range Selector
The Angular Range selector allows a digital pre-selection of the angular range. The AS5046 can be configured for a
full scale angular range of 45°, 90°, 180° or 360°. In addition, the Output voltage versus angle response can be fine-
tuned by setting the gain of the OP-AMP with external resistors and the maximum output voltage can be set in the
DAC.
The combination of these options allows to configure the operation range of the AS5046 for all angles up to 360° and
output voltages up to 5.5V.
The response curve for the analog output is linear for the selected range (45°/90°/180°/360°). In addition, the slope is
mirrored at 180° for 45°- and 90°- modes and has a step response at 270° for the 180°-mode. This allows the AS5046
to be used in a variety of applications. In these three modes, the output remains at V
sudden output change when the mechanical angle is rotated beyond the selected analog range. In 360°-mode, a jitter
between V
www.austriamicrosystems.com
Magnetic field range alarm. Active
low. Leave open or connect to
VSS if not used
DSP
from
CSn
Digital serial
interface, 10bit/360°.
Leave open if not
used. CSn and CLK
may also be tied to
VSS if no used
OR1
3
out,max
SCL
Analog Output Block Diagram
0 360 ° 0
0 180 ° 1
1 90 ° 0
1 45 ° 1
Selector
Range
OR0
4
SDO
MagRngn
and V
6
1
PROG
digital
10 bit
out,min
8
for OTP
programming and
alignment mode
only. Leave open
or connect to VSS
if not used
0 = 0-100 % * Vref ( def.)
1 = 10-9 0 % * Vref
at the 360° point is also prevented due to a hysteresis.
Mode pin.
Default = open
(low noise)
ClampMdEN
DAC
Vref
Mode
2
0 - 100 % VDD5 V /2
NC
REF_ extEN
5
External DAC reference pin.
Leave open or connect to
VSS if not used
Test pins .
Leave open
0= int
1= ext
NC
13
DACref
NC
Revision 1.12
14
9
analog
VDD5V / 2
10bit
VDD
VDD5V
FB_intEN
Vout
Gain = 2 x (int)
0
+
-
16
3.3V
0=ext
LDO
1=int
VSS
VDD3V3
7
DACout
Rf_int
30k
Rg_int
30k
VOUT
FB
out,max
DAC output pin.
Leave open if no used
11
OP-Amp feedback pin.
Leave open if not used.
15
10
12
Rf
+
1-10µF
and V
Connect pins 15 and 16
for VDD = 3.0 – 3.6V.
Do NOT connect for
VDD = 4.5 – 5.5V!
Rg
360 °angle
RLmin
= 4k7
out,min
C
<100pF
to avoid a
L
28 – 42