DM163030 Microchip Technology, DM163030 Datasheet - Page 46

• Manufacturer Part Number: DM163030
• Description: KIT DEV PICDEM LCD2
• Manufacturer: Microchip Technology
• Series: PICDEM™r
• Type: MCUr

Specifications of DM163030

• Contents: Evaluation Board
• Processor To Be Evaluated: PIC18F85J90
• Interface Type: RS-232
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8493
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PICDEM™ LCD 2 Demonstration Kit User’s Guide
A.3
A.4
A.5
DS51662C-page 46
LED DISPLAY
CHARGE PUMP AND VLCAP
RESISTIVE LADDER VERSUS CHARGE PUMP
TABLE A-21:
Two green LEDs are connected to RC3 and RC4 of U1A through the J14 pins, 1, 2 and
7, 8 (outer ends), respectively.
One green LED is provided to determine whether there is power to the LCD 2
Demonstration Board (LED on) or not (LED off).
For charge pump mode operation in PIC18F85J90 and PIC18F87J90 devices, it is
required that RC3 and RC4 of U1A connect to charge pump capacitor C7 through the
J14 pins, 3, 4 and 5, 6 (inner pins), respectively.
The switch, S6, allows the connection of either the resistor ladder or the capacitors to
the BIAS pins to generate the BIAS voltages for the LCD operation. For the Charge
Pump mode operation in PIC18F85J90 and PIC18F87J90 devices, it is required that
the S6 switch is flipped towards C and the VLCAP is connected through the inner
jumpers of J14. For the resistor ladder, S6 must be flipped towards R. The R45
potentiometer controls the contrast to the LCD in the Resistive Ladder mode.
A.5.1
When jumper JP21 is on, the LCDBIAS0 is physically tied to ground. The jumper needs
to be on for PIC18F85J90 and PIC18F87J90 devices when the bias voltages are
generated through the resistor ladder.
Legend:
Note 1:
PIC16F917 Port
2:
3:
RA0
RA1
RA6
RA7
RB0
RB5
RB6
RB7
RC0
RC1
RC3
RC4
RC6
RC7
Unshaded cells indicate a perfect match between the PIM and the glass.
Shaded cells indicate the pins that are remapped to the corresponding pin on the PIM.
Jumper JP21
For the PIC18F85J90 and PIC18F87J90 PIM, the RG2 and RG3 pins are
connected to RC3 and RC4 of U1A, respectively.
For the PIC16F17 PIM, the RD1 and RD2 pins are connected to RC3 and
RC4 of U1A, respectively.
For the PIC18F8490 PIM, the RC3 and RD4 pins are connected to RC3
and RC4 of U1A, respectively
PIC16F917 PIN AND PORT COMPARISON
PIC16F917 Pin
T1OSCO
T1OSCI
VLCD1
VLCD2
SEG11
RX/DT
COM1
TX/CK
SEG6
AN0
AN1
RB0
RB6
RB7
T1OSCO
T1OSCI
ICE Pin
SEG11
SEG14
COM1
TX/CK
RX/DT
BIAS1
BIAS2
AN0
AN1
RB0
RB6
RB7
 2010 Microchip Technology Inc.
ICE Port
RC0
RC1
RC6
RC7
RA0
RA1
RB0
RE4
RB6
RB7
RE0
RE1
RB4
RA4