DC-ME-01T-KT Digi International, DC-ME-01T-KT Datasheet - Page 71
DC-ME-01T-KT
Manufacturer Part Number
DC-ME-01T-KT
Description
KIT INTEGRATION ME MOD S MODELS
Manufacturer
Digi International
Series
Digi Connect ME®r
Type
MCU Moduler
Specifications of DC-ME-01T-KT
Contents
Module with plug-and-play firmware, Development Board, Documentation, CD, Cables and Power Supply
Silicon Manufacturer
Digi Intl
Kit Application Type
Communication & Networking
Application Sub Type
Embedded
Silicon Family Name
Digi Connect ME
Rohs Compliant
Yes
For Use With/related Products
Digi Connect ME S Module
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
602-1057
- Current page: 71 of 155
- Download datasheet (3Mb)
Configuring the IP Address from the Command-Line Interface
Connectware Manager
Testing the IP Address Configuration
The set network command is used to configure an IP address from the command line. To
configure the Digi Connect SP through the command line, the DIP switches must be
changed. See "Command Line Access" on page 66 for an illustration of the DIP switch
settings. On the set network command, include the following parameters:
For example:
The IP address cannot be set in Connectware Manager but it can be changed.
Open the browser based on the IP address the device has and go to Configuration >
Network > IP Settings and enter the new IP address, subnet mask, and gateway.
Once the IP address is assigned, you should test the IP address configuration to be sure it
works as configured.
Prerequisite
This procedure assumes that you have configured the device server with an IP address.
Procedure
1
2
ip=device ip: The IP address for the device.
gateway=gateway: The network gateway IP address.
submask=device submask: The device submask.
dhcp=off: Turns off use of the Dynamic Host Configuration Protocol (DHCP),
so that the IP address assigned is permanent.
static=on: Specifies that the IP address is static, and will remain as the specified
IP address, gateway, and submask.
Access the command line of a PC or other networked device.
Issue the following command:
set network ip=10.0.0.1 gateway=255.255.255.0
submask=255.255.255.0 dhcp=off static=on
C o n f i g u r i n g t h e D i g i C o n n e c t D e v i c e s
7 1
Related parts for DC-ME-01T-KT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
ME 9210 8MB SDRAM 4MB FLASH SGL
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ENCRYPTION ENGINE 10/100 INT
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH SINGLE
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH 10 PAK
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH 10 PAK
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MOD ME 9210 8MB SDRAM 2MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MOD ME 9210 8MB SDRAM 4MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE ME CUSTOMIZABLE JTAG
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE ME 8MB SDRAM 2MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE ME 8MB SDRAM 2MB FLASH
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 9210 8MB RAM 4MB FLASH LINUX
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH 50 PAK
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
ME 8MB SDRAM 2MB FLASH 50 PAK
Manufacturer:
Digi International
Datasheet:
Part Number:
Description:
MODULE ME 8MB SDRAM 2MB FLASH
Manufacturer:
Digi International
Datasheet: