101-0577 Rabbit Semiconductor, 101-0577 Datasheet - Page 97
101-0577
Manufacturer Part Number
101-0577
Description
KIT DEV FOR BL2500 COYOTE
Manufacturer
Rabbit Semiconductor
Series
Coyoter
Type
Single Board Computers (SBC)r
Datasheet
1.101-0576.pdf
(106 pages)
Specifications of 101-0577
Contents
SBC, Dev. Board, AC Adapter, Cable and Dynamic C® CD-ROM
Product
Modules
Data Bus Width
10 bit
Processor Type
Rabbit 3000
Sram
128 KB
Flash
256 KB
Number Of I/os
24
Backup Battery
3 V Lithium Coin Type
Operating Voltage
8 V to 40 V
Power Consumption
1 W
Board Size
100 mm x 100 mm x 29 mm
Description/function
Computer Module
Interface Type
Ethernet
For Use With/related Products
BL2510
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
- Current page: 97 of 106
- Download datasheet (2Mb)
PARAMETERS
RETURN VALUE
PARAMETERS
RETURN VALUE
User’s Manual
int rn_reset(int handle, int resettype);
int rn_sw_wdt(int handle, float timeout);
Sends a reset sequence to the specified peripheral card. The reset takes approximately 25 ms before the
peripheral card will once again execute the application. Allow 1.5 seconds after the reset has completed
before accessing the peripheral card. This function will check peripheral card information to determine
that the peripheral card is connected to a master.
handle is an address index to device information. Use rn_device() or rn_find() to establish the
handle.
resettype describes the type of reset.
The status byte from the previous command. -1 means that device information indicates the peripheral
card is not connected to the master.
Sets software watchdog timeout period. Call this function prior to enabling the software watchdog timer.
This function will
handle is an address index to device information. Use rn_device() or rn_find() to establish the
handle.
timeout is a timeout period from 0.025 to 6.375 seconds in increments of 0.025 seconds. Entering a
zero value will disable the software watchdog timer.
The status byte from the previous command. -1 means that device information indicates the peripheral
card is not connected to the master.
0 = hard reset—equivalent to power-up. All logic is reset.
1 = soft reset—only the microprocessor logic is reset.
check device information to determine that the peripheral card is connected to a master.
91
Related parts for 101-0577
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SNGLBD BL2101 A/D 0-10V
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
CARD D/A 0-10V SR9400 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
CARD A/D 0-10V SR9300 SMARTSTAR
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
WiFi / 802.11 Modules & Development Tools WIRELESS CONTROL APP KIT
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
KIT DEV RABBITCORE RCM3750
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RABBIT 2000 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEV RABBIT RCM2000 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
KIT DEVELOPMENT RCM3700 INT'L
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
BL4S200 TOOL KIT
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3720
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3220
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
MODULE RABBITCORE RCM3210
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD OP6600 W/SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BD BL2000 SRAM/FLSH
Manufacturer:
Rabbit Semiconductor