8.12.00 J-LINK ARM-PRO Segger Microcontroller Systems, 8.12.00 J-LINK ARM-PRO Datasheet - Page 178
![JTAG EMULATOR USB ETHERNET ARM](/photos/9/27/92737/8_12_00-j-link-arm-pro_sml.jpg)
8.12.00 J-LINK ARM-PRO
Manufacturer Part Number
8.12.00 J-LINK ARM-PRO
Description
JTAG EMULATOR USB ETHERNET ARM
Manufacturer
Segger Microcontroller Systems
Type
Emulatorr
Specifications of 8.12.00 J-LINK ARM-PRO
Contents
Emulation Module
For Use With/related Products
ARM7, ARM9, ARM11, Cortex
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
8.12.00 J-LINK ARM-PRO
899-1007
899-1007
- Current page: 178 of 222
- Download datasheet (3Mb)
178
8.2.2
J-Link / J-Trace (UM08001)
The following table lists the JTAG+Trace connector pinout. It is compatible to the
"Trace Port Physical Interface" described in [ETM], 8.2.2 "Single target connector
pinout".
Table 8.5: JTAG+Trace connector pinout
10
11
12
13
14
15
16
17
18
19
20
21
PIN
1
2
3
4
5
6
7
8
9
Pinout
NC
NC
NC
NC
GND
TRACECLK
DBGRQ
DBGACK
RESET
EXTTRIG
TDO
VTRef
RTCK
VSupply
TCK
Trace signal 12
TMS
Trace signal 11
TDI
Trace signal 10
nTRST
SIGNAL
No connected.
No connected.
No connected.
No connected.
Signal ground.
Clocks trace data on rising edge or both edges.
Debug request.
Debug acknowledge from the test chip, high when in
debug state.
Open-collector output from the run control to the target
system reset.
Optional external trigger signal to the Embedded trace
Macrocell (ETM). Not used. Leave open on target system.
Test data output from target JTAG port.
Signal level reference. It is normally fed from Vdd of the
target board and must not have a series resistor.
Return test clock from the target JTAG port.
Supply voltage. It is normally fed from Vdd of the target
board and must not have a series resistor.
Test clock to the run control unit from the JTAG port.
Trace signal. For more information, please refer to
Assignment of trace information pins between ETM archi-
tecture versions on page 180.
Test mode select from run control to the JTAG port.
Trace signal. For more information, please refer to
Assignment of trace information pins between ETM archi-
tecture versions on page 180.
Test data input from run control to the JTAG port.
Trace signal. For more information, please refer to
Assignment of trace information pins between ETM archi-
tecture versions on page 180.
Active-low JTAG reset
CHAPTER 8
© 2004-2011 SEGGER Microcontroller GmbH & Co. KG
Description
Target interfaces and adapters
Related parts for 8.12.00 J-LINK ARM-PRO
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![8.07.00 JTAG ISOLATOR](/photos/8/98/89840/8_07_00-jtag-isolator_tmb.jpg)
Part Number:
Description:
CONNECTOR JTAG-ARM ISOLATION
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.01 J-LINK ARM-14](/photos/9/0/90082/mfg_8_08_01_j-link_arm-14_tmb.jpg)
Part Number:
Description:
ADAPTER ARM TARGET 14PIN RIBBON
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.00 J-LINK ARM](/photos/9/26/92680/8_08_00_j-link_arm_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.08.90 J-LINK EDU](/photos/9/27/92725/8_08_90-j-link-edu_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.05.01 FLASHER 5](/photos/9/27/92731/5_05_01-flasher-5_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.04.01 FLASHER ST7](/photos/9/27/92732/5_04_01_flasher_st7_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR ST7 MCU
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.09.01 FLASHER STM 8](/photos/9/27/92733/5_09_01-flasher-stm-8_tmb.jpg)
Part Number:
Description:
PROGRAMMING TOOL FOR STM8
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![5.07.01 FLASHER ARM](/photos/9/27/92734/5__07_01_flasher_arm_tmb.jpg)
Part Number:
Description:
PROGRAMMER JTAG FOR ARM CORES
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.10.00 J-TRACE ARM](/photos/9/27/92738/8_10_00-j-trace-arm_tmb.jpg)
Part Number:
Description:
JTAG EMULATOR ARM7/ARM9 ETM
Manufacturer:
Segger Microcontroller Systems
Datasheet:
![8.13.00 J-TRACE FOR CORTEX-M3](/images/no-image3.png)
Part Number:
Description:
EMULATOR JTAG/SWD CORTEX M3
Manufacturer:
Segger Microcontroller Systems
Datasheet: