LCE-789014-EM Renesas Electronics America, LCE-789014-EM Datasheet
LCE-789014-EM
Specifications of LCE-789014-EM
Related parts for LCE-789014-EM
LCE-789014-EM Summary of contents
Page 1
To our customers, Old Company Name in Catalogs and Other Documents st On April 1 , 2010, NEC Electronics Corporation merged with Renesas Technology Corporation, and Renesas Electronics Corporation took over all the business of both companies. Therefore, although the ...
Page 2
All information included in this document is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas Electronics products listed herein, please confirm ...
Page 3
... User’s Manual Introduction The LCE-789014- emulation board or daughterboard for the LCE-K0S development system for NEC’s 8-bit PD789014 subseries microcontrollers. Combining this board with the LCE-78K0S allows you to efficiently emulate any PD789014 subseries device. The LCE- 789014-EM is shipped with the following contents: ...
Page 4
... Target device Clock supply Low-voltage compatible Components The LCE-789014-EM daughterboard mates with the LCE-78K0S motherboard. In other words, the top of the daughterboard faces down in the system. As shown in Figure 2, a top view of the daughterboard the Realchip that provides peripherals unique to the PD789014 subseries devices. ...
Page 5
... The side of the ribbon cable with a red stripe is pin 1. Table 2. P1 Pin Assignment P1 Connector LCE-789014-EM Emulation Board PD78901x Signal Device Pin 1 P31/INTP1/TI1/TO1 2 P32/INTP2 Note GND on probe cable GND on probe cable GND on probe cable GND on probe cable GND on probe cable GND on probe cable GND on probe cable ...
Page 6
... LCE-789014-EM Emulation Board Table 2. P1 Pin Assignments (continued) P1 Connector PD78901x Signal Device Pin 3 VPP 4 RESET VSS 8 VDD 9 P00 10 P01 11 P02 12 P03 13 P04 14 P05 15 P06 16 P07 17 P10 18 P11 19 P12 20 P13 21 P14 22 P15 23 P16 24 P17 25 P20/ASCK/SCK0 26 P21/TXD/SO0 27 P22/RXD/SI0 28 P30/INTP0/TI0/TO0 Note GND on probe cable ...
Page 7
... Table 3. Emulation Probe Pin Assignments Emulation Device Pin No. Table 4. Emulation Probe and Socket for PD789014 Subseries Target Device PD789011GT PD789012GT PD78P9014GT PD789011CT PD789012CT PD78P9014CT LCE-789014-EM Emulation Board J1 Pin No. Emulation Device Pin No 102 5 ...
Page 8
... LCE-789014-EM Emulation Board Assembly This procedure explains how to connect the LCE-789014-EM to the LCE-78K0S motherboard. 1. Connect the probe or ribbon cable to their respective connectors on the LCE-789014-EM (Figure 4). Figure 4. Connections for Emulation Probe or Ribbon Cables 2. Make sure power is off from the LCE-K0S motherboard. 3. Remove the two screws at the bottom of the standoffs on the motherboard (Figure 5). ...
Page 9
... A pply P ress ure othe rbo ard 5. Replace the screws on the bottom of the daughterboard to securely connect it to the motherboard (Figure 7). Figure 7. Connection to Motherboard 6. Connect the loose end of the probe or ribbon cable to the user target. Refer to Table 2 and Table 3 for pin assignments. LCE-789014-EM Emulation Board 7 ...
Page 10
... With a 25-pin male-to-male parallel cable (not included), connect the LCE-K0S system to the host computer (Figure 8). Figure 8. Connection to Host PC 8. With the power adapter connected, turn the switch to the ON position. The green LED turns on when power is supplied to the system. 9. Launch the debugger from your PC. ...
Page 11
In North America: No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics Inc. (NECEL). The information in this document is subject to change without ...
Page 12
In North America: No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Electronics Inc. (NECEL). The information in this document is subject to change without ...