AD9510/PCB Analog Devices Inc, AD9510/PCB Datasheet - Page 32

• Manufacturer Part Number: AD9510/PCB
• Description: IC CLOCK DISTRIB PLL 64LFCSP
• Manufacturer: Analog Devices Inc

Specifications of AD9510/PCB

• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD9510
PLL Analog Lock Detect
An analog lock detect (ALD) signal may be selected. When
ALD is selected, the signal at the STATUS pin is either an
open-drain P-channel (08h<5:2> = 1100) or an open-drain
N-channel (08h<5:2> = 0101b).
The analog lock detect signal is true (relative to the selected
mode) with brief false pulses. These false pulses get shorter as
the inputs to the PFD are nearer to coincidence and longer as
they are further from coincidence.
To extract a usable analog lock detect signal, an external RC
network is required to provide an analog filter with the
appropriate RC constant to allow for the discrimination of a
lock condition by an external voltage comparator. A 1 kΩ
resistor in parallel with a small capacitance usually fulfills this
requirement. However, some experimentation may be required
to get the desired operation.
The analog lock detect function may introduce some spurious
energy into the clock outputs. It is prudent to limit the use of
the ALD when the best possible jitter/phase noise performance
is required on the clock outputs.
Loss of Reference
The AD9510 PLL can warn of a loss-of-reference signal at
REFIN. The loss-of-reference monitor internally sets a flag
called LREF. Externally, this signal can be observed in several
ways on the STATUS pin, depending on the PLL MUX control
settings in Register 08h<5:2>. The LREF alone can be observed
as an active high signal by setting 08h<5:2> = <1010> or as an
active low signal by setting 08h<5:2> = <1111>.
The loss-of-reference circuit is clocked by the signal from the
VCO, which means that there must be a VCO signal present in
order to detect a loss of reference.
LOSS OF REFERENCE OR LOCK DETECT (ACTIVE HIGH)
LOSS OF REFERENCE OR LOCK DETECT (ACTIVE LOW)
ANALOG LOCK DETECT (N-CHANNEL OPEN DRAIN)
ANALOG LOCK DETECT (P-CHANNEL OPEN DRAIN)
DIGITAL LOCK DETECT (ACTIVE HIGH)
DIGITAL LOCK DETECT (ACTIVE LOW)
LOSS OF REFERENCE (ACTIVE HIGH)
LOSS OF REFERENCE (ACTIVE LOW)
PRESCALER OUTPUT (NCLK)
Figure 37. STATUS Pin Circuit CLK1 Clock Input
OFF (LOW) (DEFAULT)
A COUNTER OUTPUT
N DIVIDER OUTPUT
R DIVIDER OUTPUT
PFD DOWN PULSE
PFD UP PULSE
Rev. A | Page 32 of 60
TRI-STATE
PLL MUX CONTROL
08h <5:2>
The digital lock detect (DLD) block of the AD9510 requires a
PLL reference signal to be present in order for the digital lock
detect output to be valid. It is possible to have a digital lock
detect indication (DLD = true) that remains true even after a
loss-of-reference signal. For this reason, the digital lock detect
signal alone cannot be relied upon if the reference has been lost.
There is a way to combine the DLD and the LREF into a single
signal at the STATUS pin. Set 08h<5:2> = <1101> to get a signal
that is the logical OR of the loss-of-lock (inverse of DLD) and
the loss-of-reference (LREF) active high. If an active low version
of this same signal is desired, set 08h<5:2> = <1110>.
The reference monitor is enabled only after the DLD signal has
been high for the number of PFD cycles set by the value in
07h<6:5>. This delay is measured in PFD cycles. The delay
ranges from 3 PFD cycles (default) to 24 PFD cycles. When the
reference goes away, LREF goes true and the charge pump goes
into tri-state.
User intervention is required to take the part out of this state.
First, 07h<2> = 0b must be written to disable the loss-of-
reference circuit, taking the charge pump out of tri-state and
causing LREF to go false. A second write of 07h<2> = 1 is
required to re-enable the loss-of-reference circuit.
WRITE 07h<2> = 0
LREF SET FALSE
CHARGE PUMP COMES
OUT OF TRI-STATE
WRITE 07h<2> = 1
LOR ENABLED
GOES INTO TRI-STATE.
SYNC DETECT ENABLE
LREF SET TRUE.
DETECT
CHARGE PUMP
SYNC
58h <0>
Figure 38. Loss of Reference Sequence of Events
PLL LOOP LOCKS
DLD GOES TRUE
LREF IS FALSE
REFERENCE
DETECTED
GND
MISSING
V
S
STATUS
PIN
REFERENCE IS DETECTED.
CHECK FOR PRESENCE
LREF STAYS FALSE IF
OR REFERENCE.
n PFD CYCLES WITH
DLD TRUE
(n SET BY 07h<6:5>)