HA5024EVAL Intersil, HA5024EVAL Datasheet
![no-image](/images/manufacturer_photos/0/3/341/intersil_sml.jpg)
HA5024EVAL
Specifications of HA5024EVAL
Related parts for HA5024EVAL
HA5024EVAL Summary of contents
Page 1
... HA5024IBZ96 HA5024IBZ - (See Note) HA5024EVAL High Speed Op Amp DIP Evaluation Board *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free plus anneal products employ special Pb-free ma- terial sets ...
Page 2
Absolute Maximum Ratings Voltage Between V+ and V- Terminals . . . . . . . . . . . . . . . . . . . 36V DC Input Voltage (Note ...
Page 3
Electrical Specifications V SUPPLY PARAMETER -IN Power Supply Rejection Input Noise Voltage +Input Noise Current -Input Noise Current TRANSFER CHARACTERISTICS Transimpedence Open Loop DC Voltage Gain Open Loop DC Voltage Gain OUTPUT CHARACTERISTICS Output Voltage Swing Output Current Output Current, ...
Page 4
Electrical Specifications V SUPPLY PARAMETER AC CHARACTERISTICS ( 681Ω Slew Rate Full Power Bandwidth Rise Time Fall Time Propagation Delay Overshoot -3dB Bandwidth Settling Time to 1% Settling Time to 0.25% Gain Flatness AC ...
Page 5
Test Circuits and Waveforms FIGURE 1. TEST CIRCUIT FOR TRANSIMPEDANCE MEASUREMENTS (NOTE 17) 100Ω DUT 50Ω 1kΩ F FIGURE 2. SMALL SIGNAL PULSE RESPONSE CIRCUIT NOTE: 17. A series input resistor of ≥100Ω is ...
Page 6
Schematic (One Amplifier of Four 800 2.5K 15K 1.25K 60K R 7 15K Q N1 DIS ...
Page 7
Application Information Optimum Feedback Resistor The plots of inverting and non-inverting frequency response, see Figure 11 and Figure 12 in the Typical Performance Curves section, illustrate the performance of the HA5024 in various closed loop gain configurations. Although the bandwidth ...
Page 8
The circuit shown in Figure simplified schematic of the enable/disable function. The large value resistors in series with the DISABLE pin makes it appear as a current source to the driver. When the driver pulls this pin ...
Page 9
Referring to Figure 10, both inputs are terminated in their characteristic impedance; 75Ω is typical for video applications. Since the drivers usually are terminated in their characteristic impedance the input gain is 0.5, thus the amplifiers are configured ...
Page 10
Typical Performance Curves 0.2V OUT P 10pF 681Ω 1kΩ 10, ...
Page 11
Typical Performance Curves 200 350 500 650 FEEDBACK RESISTOR (Ω) FIGURE 17. BANDWIDTH vs FEEDBACK RESISTANCE 0.10 0. 75Ω 150Ω L 0.04 0. 1kΩ L 0.00 3 ...
Page 12
Typical Performance Curves 8 100Ω 1.0V OUT P 7.5 7.0 6.5 6.0 -50 - TEMPERATURE (°C) FIGURE 23. PROPAGATION DELAY vs TEMPERATURE 500 OUT P-P ...
Page 13
Typical Performance Curves 1.5 1.0 0.5 0.0 -60 -40 - TEMPERATURE (°C) FIGURE 29. INPUT OFFSET VOLTAGE vs TEMPERATURE -60 -40 - TEMPERATURE (°C) FIGURE 31. -INPUT BIAS ...
Page 14
Typical Performance Curves 40 +10V 30 + DISABLE INPUT VOLTAGE (V) FIGURE 35. SUPPLY CURRENT vs DISABLE INPUT VOLTAGE 0.01 0.10 LOAD RESISTANCE (kΩ) ...
Page 15
Typical Performance Curves - OUT P-P -40 -50 -60 -70 -80 0.1 1 FREQUENCY (MHz) FIGURE 41. CHANNEL SEPARATION vs FREQUENCY DISABLE = P 750Ω ...
Page 16
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...