PCWHD IDE COMPILER Custom Computer Services Inc (CCS), PCWHD IDE COMPILER Datasheet - Page 158
PCWHD IDE COMPILER
Manufacturer Part Number
PCWHD IDE COMPILER
Description
PCWHD PIC10,16,18,24, DSPIC
Manufacturer
Custom Computer Services Inc (CCS)
Type
Compilerr
Datasheet
1.PCD_COMMAND_LINE_COMPILER.pdf
(373 pages)
Specifications of PCWHD IDE COMPILER
For Use With/related Products
Microchip PIC10, PIC12, PIC16, PIC18, PIC24, dsPIC MCUs
Lead Free Status / RoHS Status
Not applicable / Not applicable
Other names
429-1009
- Current page: 158 of 373
- Download datasheet (4Mb)
144
BRGH1OK
ENABLE=pin
DEBUGGER
RESTART_WDT
INVERT
PARITY=X
BITS =X
FLOAT_HIGH
ERRORS
SAMPLE_EARLY
RETURN=pin
MULTI_MASTER
Allow bad baud rates on chips that have baud rate
problems.
The specified pin will be high during transmit. This
may be used to enable 485 transmit.
Indicates this stream is used to send/receive data
though a CCS ICD unit. The default pin used in B3,
use XMIT= and RCV= to change the pin used. Both
should be the same pin.
Will cause GETC() to clear the WDT as it waits for a
character.
Invert the polarity of the serial pins (normally not
needed when level converter, such as the MAX232).
May not be used with the internal UART.
Where x is N, E, or O.
Where x is 5-9 (5-7 may not be used with the SCI).
The line is not driven high. This is used for open
collector outputs. Bit 6 in RS232_ERRORS is set if
the pin is not high at the end of the bit time.
Used to cause the compiler to keep receive errors in
the variable RS232_ERRORS and to reset errors
when they occur.
A getc() normally samples data in the middle of a bit
time. This option causes the sample to be at the
start of a bit time. May not be used with the UART.
For FLOAT_HIGH and MULTI_MASTER this is the
pin used to read the signal back. The default for
FLOAT_HIGH is the XMIT pin and for
MULTI_MASTER the RCV pin.
Uses the RETURN pin to determine if another
master on the bus is transmitting at the same time. If
a collision is detected bit 6 is set in
RS232_ERRORS and all future PUTC's are ignored
until bit 6 is cleared. The signal is checked at the
start and end of a bit time. May not be used with the
UART.
Related parts for PCWHD IDE COMPILER
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PROTOTYPING BOARD FOR PIC MCU
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
Extra CCS C Manual
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
MACH X Programmer
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PCD For 24-bit (PIC24/dsPIC)
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
LOAD-n-GO Programmer
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
EMBEDDED INTERNET DEVELOPMENT KIT W/PCWH
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PIC24F Development Kit With PCWHD
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PIC24F Development Kit With PCDIDE
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PIC24H Development Kit With PCWHD
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PIC24H Development Kit With PCDIDE
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PIC18F6722 Embedded C Development Kit With PCWH Compiler
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
PIC18F8722 Embedded C Development Kit With PCWH Compiler
Manufacturer:
Custom Computer Services Inc (CCS)
Part Number:
Description:
USB Master Prototyping Board
Manufacturer:
Custom Computer Services Inc (CCS)