QW1 TechTools, QW1 Datasheet - Page 13

• Manufacturer Part Number: QW1
• Description: PROGRAMMER PIC MCU QUICKWRITER
• Manufacturer: TechTools
• Series: QuickWriter™r
• Type: QuickWriterr

Specifications of QW1

• Contents: MCU Programmer with In-Circuit Serial Programming Cable and Optional GANG Adapters
• For Use With/related Products: PIC Micro® MCU
• For Use With: CBL-ICSP - CABLE PROG QUICKWRITER SERIALQW-4SSOP18 - ADAPTER QUICKWRITER 4GANG 18SSOPQW-4SSOP28 - ADAPTER QUICKWRITER 4GANG 28SSOPQW-4SO8/14W - ADAPT QUICKWRTR 4GANG 8/14SOIC WQW-4SO8/14N - ADAPT QUICKWRTR 4GANG 8/14SOIC NQW-4SOIC18 - ADAPTER QUICKWRITER 4GANG 18SOICQW-4ZIF18 - ADAPTER QUICKWRITER 4-GANG 18ZIFQW-4SOIC28 - ADAPTER QUICKWRITER 4GANG 28SOICQW-4PLCC44 - ADAPTER QUICKWRITER 4GANG 44PLCCQW-4ZIF40/28 - ADAPT QUICKWRITER 4GANG 40/28ZIFMP-ZIF14 - ADAPTER QUICKWRITER 14-PIN ZIFMP-SOIC8/14 - ADAPTER QUICKWRITER 8/14-SOICMP-SSOP18 - ADAPTER QUICKWRITER 18-SSOPMP-SSOP28 - ADAPTER QUICKWRITER 28-SSOPMP-14000 - ADAPTR QUICKWRTR PIC14000 28-PINMP-SOIC18 - ADAPTER QUICKWRITER 18-SOICMP-SOIC28 - ADAPTER QUICKWRITER 28-SOICMP-PLCC44 - ADAPTER QUICKWRITER 44-PIN PLCCMP-ZIF18/28 - ADAPTER QUICKWRITER 18/28PIN ZIFMP-ZIF40 - ADAPTER QUICKWRITER 40-PIN ZIF

© 2007 TechTools
2.2.2
Shortcuts
Setting General Options
Overview
MCU Sections:
General options that are not normally needed during development but help when preparing
settings for production personnel.
Alt+O, O
device during Auto Run cycles. We suggest leaving this option enabled unless reprogramming
an MCU that already contains data.
Enable Verify - If selected, a verify will be performed during Auto Run cycles on all selected
areas of the MCU (i.e. Code, EE Data, Calibration, ID) before the Configuration Word is
programmed. Most programming operations automatically verify during programming, but
because some MCU algorithms do not, we suggest always leaving this option enabled.
Enable Serial Numbering - If selected, the MCU will be serialized (just prior to programming the
Configuration word) during Auto Run cycles according to the settings in
Enable Code - If selected, the Code Space area will be blank checked, programmed and
verified during Auto Run cycles according to Operation settings.
Enable EE Data - If selected, the EE Data area will be programmed and verified during Auto
Run cycles.
Enable ID Locations - If selected, the ID locations will be blank checked, programmed and
verified during Auto Run cycles. ID locations have no bearing on the operation of the MCU and
can be ignored if desired.
Enable Calibration - If available for the MCU and selected, the Calibration area will be blank
checked, programmed and verified during Auto Run cycles. Some FLASH MCUs with calibration
require this option and QuickWriter will automatically select it for you. If the MCU is not a FLASH
device, we strongly advise against selecting this option unless programming a JW
(windowed) device. Attempting to program the calibration area of an OTP (one time
programmable) device will result in corrupted calibration data.
Enable Fuses - If selected, the Configuration Word will be programmed and verified during Auto
Run cycles.
10
(also see:
Using Serial Numbers
17
).
QuickWriter MCU Programmer
Serial Number options
7