QW1 TechTools, QW1 Datasheet - Page 71

• Manufacturer Part Number: QW1
• Description: PROGRAMMER PIC MCU QUICKWRITER
• Manufacturer: TechTools
• Series: QuickWriter™r
• Type: QuickWriterr

Specifications of QW1

• Contents: MCU Programmer with In-Circuit Serial Programming Cable and Optional GANG Adapters
• For Use With/related Products: PIC Micro® MCU
• For Use With: CBL-ICSP - CABLE PROG QUICKWRITER SERIALQW-4SSOP18 - ADAPTER QUICKWRITER 4GANG 18SSOPQW-4SSOP28 - ADAPTER QUICKWRITER 4GANG 28SSOPQW-4SO8/14W - ADAPT QUICKWRTR 4GANG 8/14SOIC WQW-4SO8/14N - ADAPT QUICKWRTR 4GANG 8/14SOIC NQW-4SOIC18 - ADAPTER QUICKWRITER 4GANG 18SOICQW-4ZIF18 - ADAPTER QUICKWRITER 4-GANG 18ZIFQW-4SOIC28 - ADAPTER QUICKWRITER 4GANG 28SOICQW-4PLCC44 - ADAPTER QUICKWRITER 4GANG 44PLCCQW-4ZIF40/28 - ADAPT QUICKWRITER 4GANG 40/28ZIFMP-ZIF14 - ADAPTER QUICKWRITER 14-PIN ZIFMP-SOIC8/14 - ADAPTER QUICKWRITER 8/14-SOICMP-SSOP18 - ADAPTER QUICKWRITER 18-SSOPMP-SSOP28 - ADAPTER QUICKWRITER 28-SSOPMP-14000 - ADAPTR QUICKWRTR PIC14000 28-PINMP-SOIC18 - ADAPTER QUICKWRITER 18-SOICMP-SOIC28 - ADAPTER QUICKWRITER 28-SOICMP-PLCC44 - ADAPTER QUICKWRITER 44-PIN PLCCMP-ZIF18/28 - ADAPTER QUICKWRITER 18/28PIN ZIFMP-ZIF40 - ADAPTER QUICKWRITER 40-PIN ZIF

© 2007 TechTools
3.2.1.8.3 Build Preferences
3.2.1.8.4 Debug Preferences
Animation Step Delay
Verbose Build log
Log Warnings
Abort After
Run To MAIN on reset
Halt ONLY on Source Lines
Step OUT of unknown code
Always Build All
Whenever program execution is halted, the PC speaker will emit a short beep.
During single-stepping and animating, it may be desirable to slow down the
execution speed in order to view the changes taking place, without having to halt
the program. This option gives you a sliding scale to set the minimum delay from
100 msec to 999 msec. Note: Delays can be longer than this setting, depending on
the speed of the computer running the TDE software. However, this option doe s
set the minimum delay, preventing these modes from running faster; even if other,
heavily updated windows are closed.
When selected, ALL project files will be built whenever any of the Editor files have
been updated. When NOT selected, only modified files will be re-built.
When selected, additional information will display in the build log during the build
process, providing a detailed view of events.
When selected, warning messages will be included in the Build Log.
Build will abort if the number of warnings or error messages exceed the numbers
specified here.
When Selected, Mathias will execute all code from the reset vector of the
Emulated PICmicro MCU at Full speed until a "MAIN" function or Label is
encountered. If NOT selected, Mathias will halt at the reset vector.
If Selected, Mathias will continue to run on a halt request until a source line
reference is found for the code being executed. If NOT selected, Mathias will halt
immediately when requeste d.
When selected, any STEP operation will run full speed through compiled code that
does not have a source line reference.
TechTools Design Environment
65