90759-2 Tyco Electronics, 90759-2 Datasheet

DIE SET FOR PRO-C III 22-20,18

90759-2

Manufacturer Part Number
90759-2
Description
DIE SET FOR PRO-C III 22-20,18
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Die Crimp Toolr
Datasheets
1.90759-1.pdf (6 pages)
2.58614-2.pdf (6 pages)
3.90759-1.pdf (6 pages)

Specifications of 90759-2

Connector Type
Crimp Terminals
Crimp Handle
A9996-ND
Crimp Or Cable Size
18-22 AWG
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Tool for crimping terminals
For Use With
A25585 - PROCRIMPER III W/DIE 18, 20-22
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A30040
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
{ Supplied with die assembly. Also available separately.
} Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool
Assembly 90759--1 consists of Die Assembly
90759--2 and PRO--CRIMPER III Hand Crimping Tool
Frame 354940--1. The die assembly consists of
crimping dies and a locator assembly.
Read these instructions thoroughly before crimping
E2009 Tyco Electronics Corporation, Harrisburg, PA
All International Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products, logos, and company names used are the property of their respective owners.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool and
is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. Tyco Electronics offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Tooling Assistance Center at 1- - 800- - 722- - 1111.
TE Die Assembly
TE Die Assembly
90759 2
90759--2
Die Assembly
Locator Assembly
(Supplied with
Die Assembly)
Assembly{
TE Locator
TE Locator
58516 1
58516--1
Front of Tool
(Locator Side)
Moving Jaw
Ratchet
Adjustment
Wheel
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
PRO- CRIMPER* III Hand
Crimping Tool Assembly 90759- 1
with Die Assembly 90759- 2
MATE N LOK*
MATE--N--LOK*
Mini Universal
Connectors
Contact
Contact
Family}
Figure 1
any contacts.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
NOTE
Size (AWG)
18, (2) 22
i
22--20
Stationary Jaw
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
Moving Handle
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Pivot Pin
[(2) .133 max]
[.059 to .094]
(2) 3.38 max
1.50 to 2.39
Insul Dia
Wire
Back of Tool
(Wire Side)
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Stationary
Handle
Instruction Sheet
408- - 9962
06 OCT 09 Rev B
[(2) .138 to .157]
(2) 3.50 to 3.99
Strip Length
[.126 to .146]
3.20 to 3.71
OR
OR
1 of 6
LOC B

90759-2 Summary of contents

Page 1

... Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 90759--1 consists of Die Assembly 90759--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly. Read these instructions thoroughly before crimping ...

Page 2

... To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the four die retaining pins, and slide the anvils and crimpers out of the tool jaws. Tyco Electronics Corporation Tool Frame Die Retaining Pins Die Retaining ...

Page 3

... Make sure that both sides of the insulation barrel CAUTION are started evenly into the crimping section NOT attempt to crimp an improperly positioned contact. Back of Tool (Wire Side) Contact (Typ) Locator in Wire Wire Stop Slot Figure 3 Tyco Electronics Corporation Strip Length Wire Inserted to Stop ...

Page 4

... Do not use objects that could .81 [.032] damage the tool. When not in use, keep handles closed to prevent objects from becoming lodged in 1.02 [.040] the crimping dies, and store in a clean, dry area. Tyco Electronics Corporation (Figure 5) Screwdriver Lockscrew (Typ) Figure 5 ...

Page 5

... Revisions to this instruction sheet include: Changed PRO--CRIMPER II Hand Tool to S PRO--CRIMPER III Hand Tool; Revised crimp--height comparator information; S Applied TE logo; S Updated format to current corporate S requirements; and Added back page indicating tooling compatible S with dies 90759--2. Tyco Electronics Corporation ...

Page 6

... SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 Tooling Used With Dies 90759- 2 SDE PEW- 12 Hand Tool 9- 1478240- 0 626 Adapter 679304- 1 (Instruction Sheet 408- 4070) Battery Tool (Pin Die) 1213890 Tyco Electronics Corporation ...