90759-2 Tyco Electronics, 90759-2 Datasheet

DIE SET FOR PRO-C III 22-20,18

90759-2

Manufacturer Part Number
90759-2
Description
DIE SET FOR PRO-C III 22-20,18
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Type
Die Crimp Toolr
Datasheets
1.90759-1.pdf (6 pages)
2.58614-2.pdf (6 pages)
3.90759-1.pdf (6 pages)

Specifications of 90759-2

Connector Type
Crimp Terminals
Crimp Handle
A9996-ND
Crimp Or Cable Size
18-22 AWG
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Tool for crimping terminals
For Use With
A25585 - PROCRIMPER III W/DIE 18, 20-22
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
A30040
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume
applications. A wide selection of powered application equipment for extended- - use, production operations is available.
{ Supplied with die assembly. Also available separately.
} Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers.
1. INTRODUCTION
PRO--CRIMPER III Hand Crimping Tool
Assembly 90759--1 consists of Die Assembly
90759--2 and PRO--CRIMPER III Hand Crimping Tool
Frame 354940--1. The die assembly consists of
crimping dies and a locator assembly.
Read these instructions thoroughly before crimping
E2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
The PRO- - CRIMPER III Hand Crimping Tool is a “Commercial” grade tool and
is designed primarily for field installation, repair, maintenance work, or
prototyping in industrial, commercial, or institutional applications. Product
crimped with this tool will meet the crimp height requirement for hand tools in
the appropriate 114 series specification, but may not comply with other feature
parameters of the specification. TE Connectivity offers a variety of tools to
satisfy your performance requirements. For additional information, contact the
Tooling Assistance Center at 1- - 800- - 722- - 1111.
TE Die Assembly
TE Die Assembly
90759 2
90759--2
Die Assembly
Locator Assembly
(Supplied with
Die Assembly)
Assembly{
TE Locator
TE Locator
58516 1
58516--1
Front of Tool
(Locator Side)
PRO- CRIMPER* III Hand
Crimping Tool Assembly 90759- 1
with Die Assembly 90759- 2
Moving Jaw
Ratchet
Adjustment
Wheel
MATE N LOK*
MATE--N--LOK*
Mini Universal
Connectors
Contact
Contact
Family}
TOOLING ASSISTANCE CENTER 1--800--722--1111
PRODUCT INFORMATION 1--800--522--6752
Figure 1
any contacts.
Reasons for reissue are provided in Section 11,
REVISION SUMMARY.
NOTE
Size (AWG)
18, (2) 22
i
22--20
Stationary Jaw
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
Moving Handle
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
Pivot Pin
[(2) .133 max]
[.059 to .094]
(2) 3.38 max
1.50 to 2.39
Insul Dia
Wire
Back of Tool
(Wire Side)
PRO- - CRIMPER III Hand
Crimping Tool Frame
354940- - 1 (408- - 9930)
Stationary
Handle
Instruction Sheet
408- - 9962
03 MAY 11 Rev C
[(2) .138 to .157]
(2) 3.50 to 3.99
Strip Length
[.126 to .146]
3.20 to 3.71
OR
OR
1 of 6
LOC B

90759-2 Summary of contents

Page 1

... Contact the TOOLING ASSISTANCE CENTER or PRODUCT INFORMATION (see below) for specific contact part numbers. 1. INTRODUCTION PRO--CRIMPER III Hand Crimping Tool Assembly 90759--1 consists of Die Assembly 90759--2 and PRO--CRIMPER III Hand Crimping Tool Frame 354940--1. The die assembly consists of crimping dies and a locator assembly. Read these instructions thoroughly before crimping E2011 Tyco Electronics Corporation Connectivity Ltd ...

Page 2

Nut Locator Chamfer Wire Crimper Offset Wire Anvil Insulation Anvil 2. DESCRIPTION (Figures 1 and 2) The tool features a tool frame with a stationary jaw and handle, a moving jaw, a moving handle, and an adjustable ratchet that ensures ...

Page 3

CONTACT SUPPORT ADJUSTMENT The contact support is preset prior to shipment, NOTE but minor adjustment may be necessary Make a sample crimp and determine if the contact is straight, bending upward, or bending downward adjustment ...

Page 4

Hold the contact in position and squeeze the tool handles together until ratchet engages sufficiently to hold the contact in position. Do NOT deform insulation barrel or wire barrel. 5. Insert stripped wire into contact insulation and wire barrels ...

Page 5

... Order the repair kit and replaceable parts through your TE representative, or call 1--800--526--5142, or send a facsimile of your purchase order to 1--717--986--7605, or write to: CUSTOMER SERVICE (38--35) TYCO ELECTRONICS PO BOX 3608 HARRISBURG PA 17105--3608 11.REVISION SUMMARY Revisions to this instruction sheet include: Updated document to corporate requirements ...

Page 6

... SDE Bench Terminator 1490076- 2 (Customer Manual 409- 10052) Battery Tool (Shouldered Die) 1725837 (Customer Manual 409- 10053 Tooling Used With Dies 90759- 2 SDE PEW- 12 Hand Tool 9- 1478240- 0 626 Adapter 679304- 1 (Instruction Sheet 408- 4070) Battery Tool (Pin Die) 1213890 (Customer Manual 409- 10065) ...