58063-2 Tyco Electronics, 58063-2 Datasheet

HEAD ASSEMBLY TOOL FOR D-SUB CON

58063-2

Manufacturer Part Number
58063-2
Description
HEAD ASSEMBLY TOOL FOR D-SUB CON
Manufacturer
Tyco Electronics
Series
AMPLIMITE® HDE-20r
Type
Terminating Headr
Datasheets
1.58074-1.pdf (3 pages)
2.58063-2.pdf (4 pages)

Specifications of 58063-2

Connector Type
D-Sub Connector Contacts
Crimp Handle
A2031-ND, 58075-1-ND, 58338-1-ND, 931800-1-ND
Crimp Or Cable Size
20-30 AWG
Product
Tool Component
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With
58075-1 - TOOL HANDLE PNEUMATIC W/O HEAD931800-1 - ELEC PWR UNIT W/O F/TRK OR HD58338-1 - PWR BENCH ASSEMBLY W/O HEADS
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
A2032
1. INTRODUCTION
Terminating Head 58063--2 is designed to terminate
unstripped discrete wire sizes 30 through 20 AWG
onto AMPLIMITE HDE--20 all plastic connectors
(reference part number 745203--2) and metal shell
connectors (reference part number 745492--2). These
connectors contain insulation displacement contacts.
The head must be used with one of the following
power units (for operating procedure, refer to the
instructions packaged with the power unit).
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION
Features of the head and their function are as follows:
Wire inserter—forces the wire into the slotted beams
of the contact.
Wire guide—holds the connector properly in relation
to the wire.
E2010 Tyco Electronics Corporation, Berwyn, PA
All Rights Reserved
TE logo and Tyco Electronics are trademarks.
*Trademark. Other products names, logos, or company names might be trademarks of their respective owners.
Pistol Grip Manual Handle
Assembly 58074--1
Pistol Grip Pneumatic Handle
Assembly 58075--1
Pneumatic Power Bench
Assembly 58338--1
Electric Power Unit 931800--1
NOTE
i
Power Unit
Dimensions in this instruction sheet are in metric
units [with U.S. customary units in brackets].
Figures are not drawn to scale.
(Figure 1)
Feed Slide
Feed Channel
Instruction Sheet (408) or
Customer Manual (409)
Anti- - Backup
Pawl
408--6790
408--6789
408--9393
409--5746
TOOLING ASSISTANCE CENTER 1- - 800- - 722- - 1111
PRODUCT INFORMATION 1- - 800- - 522- - 6752
Terminating Head 58063- 2
For AMPLIMITE* High Density (HDE)- 20
Connectors
Figure 1
Wire Guide
Adjuster (inserter rod)—is a piston for, and regulates
the travel of, the wire inserter.
Feed slide—automatically advances the connector
after each termination.
Anti--backup pawl—prevents the connector from
moving out of position after it has been advanced by
the feed slide.
After the head is installed onto the power unit, it
serves as a guide and support for the connector
during termination. The arrow on the top of the head
indicates the direction that the connector will move in
the head. The wires are terminated onto the
connector using the insulation displacement
technique.
3. TERMINATION PROCEDURE
Make sure that the connector matches the wire size
to be terminated, then refer to Figure 2, and proceed
as follows:
NOTE
1. Align the side of the connector with the side of
the head (so that it will move in the direction of the
arrow), and slowly slide the connector into the feed
channel. Stop when the desired contact position
aligns with the wire slot.
2. Insert the wire into the wire slot until the wire
bottoms on the head.
3. Center the wire in the wire slot, then actuate the
power unit until the wire inserter bottoms (the wire
inserter will retract, and the connector will advance
to the next contact position).
i
Wire Inserter
If the connector cannot be inserted into the head
or if the connector is too loose in the head, refer
to Paragraph 4.2 for wire guide adjustment.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.tycoelectronics.com
Adjuster
(Inserter Rod)
Instruction Sheet
408- - 9414
20 DEC 10 Rev B
1 of 4
LOC B

58063-2 Summary of contents

Page 1

... Anti- - Backup Pawl Feed Slide Feed Channel 1. INTRODUCTION Terminating Head 58063--2 is designed to terminate unstripped discrete wire sizes 30 through 20 AWG onto AMPLIMITE HDE--20 all plastic connectors (reference part number 745203--2) and metal shell connectors (reference part number 745492--2). These connectors contain insulation displacement contacts. ...

Page 2

... Inspection Regular inspections should be performed by quality control personnel with a record of quality control inspections remaining with the personnel responsible Tyco Electronics Corporation To prevent personal injury when using electric power units, ALWAYS disconnect the electrical power supply before making any adjustments. Wire Insertion Depth Adjustment ...

Page 3

... A complete inventory should be stocked and controlled to prevent lost time when replacement of parts is necessary. Parts other than those listed should be replaced by Tyco Electronics to ensure quality and reliability. Order replacement parts through your representative, or call 1--800--526--5142, or send a facsimile of your purchase order to ...

Page 4

... SCREW, Machine, 4--40¢.750 in. L PIN, Slotted Spring ADJUSTER (Inserter Rod) SPRING, Compression ROD, Inserter SLIDE, Feed PIN, Spirol PAWL, Locator Figure 5 Corrected part number of Item 5 in Figure 5 S Tyco Electronics Corporation A 25.4 mm [1.0 in.] 10 44.45 mm [1.75 in.] 11 QTY PER HEAD 1 2 ...