58442-1 Tyco Electronics, 58442-1 Datasheet

TOOL HEAD ASSEMBLY RCPT MTA 100

58442-1

Manufacturer Part Number
58442-1
Description
TOOL HEAD ASSEMBLY RCPT MTA 100
Manufacturer
Tyco Electronics
Series
MTA-100r
Type
Hand Toolr
Datasheets
1.58442-1.pdf (4 pages)
2.58442-1.pdf (5 pages)

Specifications of 58442-1

Crimp Application
Connectors
Product
Crimping, Stripping & Cutting Tools & Drills
Description/function
Crimp tool assembly for discrete wire MTA-100 receptacles
For Use With
MTA-100 Feed-Through Receptacles
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Other names
58442-1
A9973
Feed–Through Head Assembly 58442–1 is used to
terminate discrete wires onto MTA–100 Receptacles
640620–[ ] (for wire size 22 AWG) and Receptacles
640623–[ ] (for wire size 28 AWG) with a maximum
insulation diameter of 1.52 mm [.060 in.]. Read these
instructions thoroughly before using the head.
The head must be mounted onto one of the following
tools (for operating procedure for the tool, refer to the
instructions packaged with the tool):
Reasons for reissue of this instruction sheet are
provided in Section 8, REVISION SUMMARY.
The head serves as a guide and support for the
receptacle during termination.
E
— Pistol Grip Manual Handle Assembly 58074–1
(408–6790)
— Electric Power Unit 931800–1 (409–5746)
— Pistol Grip Pneumatic Handle Assembly
58075–1 (408–6789)
— Pneumatic Power Bench Assembly 58338–1
(408–9393)
i
Dimensions in this instruction sheet are in metric
units [with U.S. customary units in brackets].
Figures are not drawn to scale.
Figure 1
Features of the head (shown in Figure 1) and
functions are as follows:
Wire inserter—forces the wire into the two slotted
beams of the contact. Note that it provides support for
the contact beams when applying insertion force on
the wire.
Rod inserter adjuster—is a piston for the wire inserter
and regulates wire inserter travel.
Feed slide—automatically positions the receptacle
after each termination.
Locating pawl—aligns the receptacle for insertion,
and retains it during termination. The locating pawl is
sometimes referred to as the “anti–backup pawl.”
Insert housing—holds the receptacle in place in
relation to the wires.
Wire subassembly retainer—holds the wires in place
in relation to the receptacle.
1. Make a termination according to Section 4,
Steps 1 through 6. If the receptacle cannot be
inserted into the head, or if the receptacle is too
loose in the head, adjust the insert housing
according to Paragraph 3.2.

58442-1 Summary of contents

Page 1

... Feed–Through Head Assembly 58442–1 is used to terminate discrete wires onto MTA–100 Receptacles 640620–[ ] (for wire size 22 AWG) and Receptacles 640623–[ ] (for wire size 28 AWG) with a maximum insulation diameter of 1.52 mm [.060 in.]. Read these instructions thoroughly before using the head. ...

Page 2

... Feed-Through Head Assembly 58442-1 2. After making the test crimp, depress the locating pawl and push the receptacle out of the RIGHT side of the head. 3. Inspect the termination according to Section 5. If necessary, make the following adjustment: — For the manual handle assembly or electric ...

Page 3

... Feed-Through Head Assembly 58442-1 the direction of the arrow) until it stops, then release the trigger or foot pedal (the receptacle should advance so that the first contact aligns with the wire inserter). 4. Check that the locating pawl is resting between the index ribs of the receptacle. See Figure 2. If not, push the receptacle out of the RIGHT side of the head, and re– ...

Page 4

... Feed-Through Head Assembly 58442-1 1. Remove dust, moisture, and other contaminants with a clean brush, or soft, lint–free cloth. DO NOT use objects that could damage the head. 2. Make sure all components are in place and properly secured. 3. Actuate the tool to ensure mechanisms inside the head move smoothly. ...

Page 5

... Feed-Through Head Assembly 58442-1 ITEM PART NUMBER through your representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 717–986–7605, or write to: CUSTOMER SERVICE (038–035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105–3608 For customer repair service, call 1–800–526–5136. ...