1-46447-0 Tyco Electronics, 1-46447-0 Datasheet

no-image

1-46447-0

Manufacturer Part Number
1-46447-0
Description
TOOL HEAD CRIMP 22-10AWG SOLIS
Manufacturer
Tyco Electronics
Series
Solistrand™, Strato-Therm™r
Datasheet
1.1-49935-0.pdf (5 pages)

Specifications of 1-46447-0

Connector Type
Terminals and Splices
Crimp Handle
1213563-1, 1213804
Crimp Or Cable Size
10-22 AWG
Lead Free Status / RoHS Status
Not applicable / Not applicable
Crimping Heads 1–46447–0, 1–69363–0 and
1–49935–0 are designed to crimp SOLISTRAND and
STRATO–THERM Terminals and Splices, and
PLASTI–GRIP Terminals and Splices onto solid or
stranded copper wire size 26–10 AWG. Refer to
Figure 2. The crimping heads are used with Double
Action Battery Powered Hand Tool Kits 1213804–[ ].
This instruction sheet provides recommended
procedures for wire preparation, crimping head
installation, crimping, and maintenance and
inspection. For information concerning tool setup and
operation, refer to Customer Manual 409–10056
packaged with the battery tool kit.
E
The crimping heads can also be used with the
626 Double Action Pneumatic Tool Adapter
1213563-1.
Dimensions are in metric units with [inches in
brackets]. Figures and illustrations are for
reference only and are not drawn to scale.
Figure 1
Reasons for reissue are provided in Section 8,
REVISION SUMMARY.
The crimping head consists of integral jaws which
close in an arc–like motion. After an operator locates
the terminal or splice between the crimping jaws and
inserts the stripped wire, the tool is activated to crimp
the terminal or splice to the wire.
Crimping heads are coated with a preservative to
prevent rust and corrosion. Wipe this preservative
from the head, particularly from the crimping
surfaces.
To avoid personal injury, be sure to exercise
extreme caution when handling the crimp tool.
Avoid accidentally depressing the trigger control
when installing or removing crimp heads.

1-46447-0 Summary of contents

Page 1

... Reasons for reissue are provided in Section 8, REVISION SUMMARY. The crimping head consists of integral jaws which close in an arc–like motion. After an operator locates the terminal or splice between the crimping jaws and inserts the stripped wire, the tool is activated to crimp the terminal or splice to the wire. ...

Page 2

... Terminal Strap Wire Strip Type Length Wire Barrel 22-16 22-16 1-46447-0 16-14 16-14 12-10 12-10 22-16 22-16 1-49935-0 16-14 16-14 12-10 12-10 26-24 26-24 1-69363-0 22-20 22-20 24-20 22-20 DO NOT operate the battery tool without the proper crimping head installed. After crimping ...

Page 3

... Remove dust, moisture, and other contaminants with a clean, soft brush lint–free cloth. Do NOT use objects that could damage the head. 2. Make sure that all pins, rings, and other components are in place and secure. ...

Page 4

... Tyco Electronics recommends the use of Molykote grease, which is a commercially available lubricant. Lubricate according to the following schedule: Head used in daily production – lubricate daily Head used daily (occasional) – lubricate weekly Head used weekly – lubricate monthly 4 ...

Page 5

... The GO element A must pass completely through the chamber as shown in Figure 5. 4. Align the NO–GO element and try to insert it into the chamber. The element may start entry, but it must not pass completely through the crimping chamber. The jaws in tool 1-49935-0 are not symmetrically NOTE located ...