1-46447-0 Tyco Electronics, 1-46447-0 Datasheet - Page 2

• Manufacturer Part Number: 1-46447-0
• Description: TOOL HEAD CRIMP 22-10AWG SOLIS
• Manufacturer: Tyco Electronics
• Series: Solistrand™, Strato-Therm™r

Specifications of 1-46447-0

• Connector Type: Terminals and Splices
• Crimp Handle: 1213563-1, 1213804
• Crimp Or Cable Size: 10-22 AWG
• Lead Free Status / RoHS Status: Not applicable / Not applicable

Remove the quick pins from the crimping head; then
remove the crimping head from the tool holder.
Wire Strip
Length
1-46447-0
1-49935-0
1-69363-0
of 5
1. Remove quick pins from the adapter assembly.
Refer to Figure 1.
2. Insert crimping head into the adapter assembly.
3. After the crimping head is properly aligned,
insert the quick pins through the two holes in the
adapter and through the holes in the crimp head.
Terminal
DO NOT operate the battery tool without the
proper crimping head installed. After crimping
head is installed, make sure that the quick pins
are properly inserted to avoid personal injury and
damage to the tool.
The quick pins will snap" into position when they
are properly inserted.
To avoid personal injury, ALWAYS disconnect the
battery from the tool before removing crimping
head.
To avoid personal injury, ALWAYS keep fingers
clear of crimping jaws when operating the tool.
Never place anything within the crimping jaws
except Tyco Electronics terminals or splices.
22-16
16-14
12-10
22-16
16-14
12-10
26-24
22-20
24-20
Wire
Barrel
22-16
16-14
12-10
22-16
16-14
12-10
26-24
22-20
22-20
Strap
Type
4 37 5 16 [ 172 203]
4.37-5.16 [.172-.203]
6.35-7.14 [.250-.281]
4 37 5 16 [ 172 203] 6 35 7 14 [ 250 281]
4.37-5.16 [.172-.203] 6.35-7.14 [.250-.281]
6.35-7.14 [.250-.281]
3.17-3.97 [.125-.156]
4.37-5.16 [.172-.203]
---
Butt Splice
Figure 2
1. Strip wire to dimensions shown in Figure 2. DO
NOT nick wire strand or use wires with nicked or
missing conductor strands.
2. Center the terminal or splice wire barrel in the
appropriate crimp chamber. For terminals, make
sure that the flat side of the tongue faces the anvil.
For splices, make sure that the brazed seam,
(when visible), is towards the indenter. See
Figure 3.
3. Depress the trigger to advance the moving ram.
This closes the crimp jaws in order to hold the
terminal in place. DO NOT deform the wire barrel.
4. Insert stripped wire into terminal or splice
making sure the wire insulation does not enter the
wire barrel.
5. Activate the tool to complete the crimp. The
crimp tool automatically returns to the first position
of the cycle when the crimp is complete.
6. To crimp the other half of the butt splice,
position the uncrimped wire barrel into the crimping
chamber, and repeat the crimping procedure. If the
splice cannot be turned for crimping the other half,
rotate the crimping head.
7. Refer to Section 5 and Figure 4 for crimp
inspection.
Not to Scale
---
---
---
---
---
6.35-7.14 [.250-.281] 7.94-8.73 [.313-.344]
6.35-7.14 [.250-.281] 7.94-8.73 [.313-.344]
3.57-4.37 [.141-.172]
5.16-5.95 [.203-.234]
4.37-5.16 [.172-.203]
Parallel Splice
---
Rev