679304-1 Tyco Electronics, 679304-1 Datasheet

TOOL PNEUMATIC HEAD ASSEMBLY

679304-1

Manufacturer Part Number
679304-1
Description
TOOL PNEUMATIC HEAD ASSEMBLY
Manufacturer
Tyco Electronics
Datasheets
1.1673606-1.pdf (8 pages)
2.679304-1.pdf (5 pages)

Specifications of 679304-1

For Use With
6-26 Series Pneumatic Tool System
Lead Free Status / RoHS Status
Not applicable / Not applicable
Lead Free Status / RoHS Status
na, Not applicable / Not applicable
Pneumatic Head Assembly 679304–1 (shown in
Figure 1) is designed to accept interchangeable die
assemblies used in PRO–CRIMPER* hand tools for
crimping various types of connectors. The head
assembly is used in the 626 Pneumatic Tooling
Assemblies 189721–1 and 189722–1. For questions
concerning the setup and operation of the pneumatic
tools, call the Tyco Electronics Tooling Assistance
Center.
This instruction sheet provides recommended
procedures for die installation and removal, crimp
head installation and removal, basic crimping
procedures, and maintenance and inspection. For
specific information concerning cable preparation and
crimping procedures, refer to the instruction sheet
packaged with the appropriate die set.
Reasons for reissue are provided in Section 7,
REVISION SUMMARY.
Remove head assembly from tool holder assembly;
then remove the two pan head screws and bushings
from the jaws of the head assembly. Select
E
Figure 1
appropriate die assembly. To install the die assembly,
proceed as follows:
1. Open crimping jaws by squeezing rollers
together. Place anvil die into the jaw of the head
assembly. See Figure 2.
2. Slide bushing over pan head screw and insert
pan head screw through the head assembly jaw
and anvil die. Tighten screw just enough to hold
the die in place.
3. Place crimper die into head assembly jaw, as
shown in Figure 2.
4. Slide bushing over pan head screw and insert
pan head screw through the head assembly jaw
and crimper die. Tighten screw just enough to hold
the die in place.
i
The die assemblies in Figure 2 are designed with
center contact crimp sections and are installed
with the crimp sections positioned toward the
front of the head assembly. If shown otherwise in
other instruction sheets, Tyco Electronics
recommends following the die installation
requirements for the specific application.

679304-1 Summary of contents

Page 1

... Pneumatic Head Assembly 679304–1 (shown in Figure 1) is designed to accept interchangeable die assemblies used in PRO–CRIMPER* hand tools for crimping various types of connectors. The head assembly is used in the 626 Pneumatic Tooling Assemblies 189721–1 and 189722–1. For questions concerning the setup and operation of the pneumatic tools, call the Tyco Electronics Tooling Assistance Center ...

Page 2

... Pneumatic Head Assembly 679304-1 Pan Head Screw(s) Crimper Die 5. Check die alignment by allowing the crimping jaws to spring shut. If dies are properly aligned, tighten the die retaining screws remove the dies from the head assembly, loosen the pan head screws and slide dies out of the crimping jaws ...

Page 3

... Pneumatic Head Assembly 679304-1 3. Connect tool to an adequate air supply between 620–690 kPa [90–100 psi]. For specific information on air line requirements and air hose installation, refer to the instructions packaged with the pneumatic tooling assembly. The pneumatic tooling assembly is now ready to be used ...

Page 4

... Replacement parts and recommended spares are listed in Figure 4. The recommended spares should be stocked for immediate replacement. Parts should be replaced by Tyco Electronics to ensure quality and reliability of the head assembly. Order replacement parts through your Tyco Electronics Representative, or call 1–800–526–5142, or send a facsimile of your purchase order to 1– ...

Page 5

... Pneumatic Head Assembly 679304-1 CUSTOMER REPLACEABLE PARTS FOR 679304-1 ITEM PART NUMBER Recommended Customer Spares C DESCRIPTION Figure 4 408-4070 QUANTITY PER ASSY 5 ...