2063778-2 Tyco Electronics, 2063778-2 Datasheet

no-image

2063778-2

Manufacturer Part Number
2063778-2
Description
CONN HAND TOOL DIE 22-18AWG
Manufacturer
Tyco Electronics
Series
Pro-Crimper™ IIIr
Datasheets
1.2063778-1.pdf (6 pages)
2.2063778-2.pdf (5 pages)

Specifications of 2063778-2

Connector Type
Hermophroditic Blade & Receptacle
Crimp Handle
2063778-1-ND
Crimp Or Cable Size
18-22 AWG
For Use With
2058302-2 - CONN SOCKET CONTACT 18-22AWG TIN2058301-2 - CONN BLADE CONTACT 18-22AWG TINA99898 - HAND TOOL PRO-CRIMPER III W/DIE
Lead Free Status / RoHS Status
Not applicable / Not applicable
{
of this page for specific contact part numbers.
PRO–CRIMPER III Hand Tool Assembly 2063778–1
consists of Die Assembly 2063778–2 and
PRO–CRIMPER III Hand Tool Frame 354940–1. The
die assembly consists of crimping dies and a locator
assembly. Read these instructions thoroughly before
crimping any contacts.
The tool features a tool frame with a stationary jaw
and handle, a moving jaw, a moving handle, and an
E
Supplied with die assembly, also available separately.
i
Dimensions on this sheet are in millimeters [with
inch equivalents provided in brackets]. Figures
and illustrations are for identification only and are
not drawn to scale.
{
}
Figure 1
}
Contact the Tooling Assistance Center at the bottom
adjustable ratchet that ensures full contact crimping.
The tool frame holds a die assembly with three
crimping sections.
The die assembly features a wire anvil, an insulation
anvil, a wire crimper, and an insulation crimper.
Attached to the outside of the frame is a locator
assembly, which contains a locator, a spring retainer,
and a contact support.
Die retaining pins and die retaining screws are used
to position and secure the dies in the tool frame. A
nut is used on the upper die retaining screw to hold
the locator assembly in place.

2063778-2 Summary of contents

Page 1

... Supplied with die assembly, also available separately. of this page for specific contact part numbers. PRO–CRIMPER III Hand Tool Assembly 2063778–1 consists of Die Assembly 2063778–2 and PRO–CRIMPER III Hand Tool Frame 354940–1. The die assembly consists of crimping dies and a locator assembly ...

Page 2

... PRO-CRIMPER III Hand Tool Assembly 2063778-1 Nut Chamfer Wire Crimper Wire Anvil 3. INSTALLATION AND REMOVAL OF DIE SET AND LOCATOR ASSEMBLY (Figure 2) 1. Open the tool handles and remove the two die retaining screws from the tool jaws. 2. Place the wire anvil and insulation anvil so that ...

Page 3

... PRO-CRIMPER III Hand Tool Assembly 2063778-1 4. Slightly loosen the nut that holds the locator assembly onto the tool frame. 5. Move the contact support as required to eliminate the bending of the contact. 6. Tighten the nut and close the handles until the ratchet releases. 7. Remove and inspect the contact. ...

Page 4

... This inspection requires the use of a micrometer with a modified anvil. Tyco Electronics recommends the modified micrometer (Crimp Height Comparator RS–1019–5LP) which may be purchased from: Shearer Industrial Supply Co. or 717–767–7575 Proceed as follows: 1. Refer to Figure 4 and select a wire (maximum size) for each crimp section listed. ...

Page 5

... PRO-CRIMPER III Hand Tool Assembly 2063778-1 PRO-CRIMPER Hand Tool 354940-1 (Instruction Sheet 408-9930) SDE Bench Terminator 1490076-2 (Customer Manual 409-10052) Battery Tool (Shouldered Die) 1725837-1, -2 (Customer Manual 409-10053) Rev A SDE PEW-12 Hand Tool 9-1478240-0 (Instruction Sheet 408-8851) 626 Adapter 679304-1 (Instruction Sheet 408-4070) ...