1. INTRODUCTION
These production torque wrenches are used to
properly install or disassemble the connectors listed in
Figure 1.
Figure 1 also contains the Tyco Electronics part
numbers for the wrenches, the previous part numbers
for the wrenches, wrench size, and the preset torque
for each wrench.
Reason for revision is provided in Section 5,
REVISION SUMMARY.
©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
TE logo is a trademark.
*Trademark. Other products, logos, and company names might be trademarks of their respective owners.
PROPER USE GUIDELINES
Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use
and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available.
PART NUMBER
ELECTRONICS
NOTE
1055276-1
1055419-1
1055840-1
1055512-1
1055546-1
1055790-1
1055791-1
1055826-1
1055868-1
1061789-1
1490262-1
i
TYCO
Open-End
Wrench Head
Dimensions on this sheet are in metric units [with
U.S. customary units in brackets], unless otherwise
noted.
PART NUMBER
2098-0351-54
2098-5065-54
2098-5304-54
2098-5619-54
2098-5830-54
2598-5026-54
2598-5027-54
2598-5160-54
2598-5298-54
7098-5031-54
2598-5383-50
PREVIOUS
Production Torque Wrench
For SMA (OSM) Type Connectors
For OSSM Type Connectors
For SMA (OSM) Hermetic Type Connectors
Production Torque Wrench Kit
For SC/N Type Connectors (Hex Nut Design)
For TNC Type Connectors (Hex Nut Design)
Production Torque Wrench
For TNC Type Connectors (Hex Nut Design)
For 7mm Type Connectors
Production Torque Wrench
Production Torque Wrenches
WRENCH DESCRIPTION
TOOLING ASSISTANCE CENTER 1-800-722-1111
PRODUCT INFORMATION 1-800-522-6752
Torque Wrench
Figure 1
2. DESCRIPTION
Each production torque wrench contains a protective
cover, a torque wrench, and an interchangeable head.
Refer to Figure 2 for the appropriate replacement
wrench head part numbers.
The wrenches are designed to be used in the
clockwise or counterclockwise direction.
3. OPERATION OF THE WRENCHES
NOTE
i
If a wrench has not been used recently, move the
wrench head back and forth several times, listening
for audible "clicks." Clicking the wrench head back
and forth spreads lubricant throughout the internal
mechanism to improve wrench performance.
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
6.4 and 8.0
20.6
15.9
14.3
19.1
mm
6.4
7.9
6.4
7.1
4.0
7.9
WRENCH SIZE
Protective Cover
INCHES ([ ])
1/4 and 5/16
13/16
5/16
9/32
5/32
9/16
5/16
1/4
1/4
5/8
3/4
Instruction Sheet
408-8676
10 MAR 11 Rev E
TORQUE
30 in.-lbs.
14 in.-lbs.
14 in.-lbs.
14 in.-lbs.
14 in.-lbs.
PRESET
18 in-lbs.
15 in.-lbs
8 in.-lbs.
8 in.-lbs.
5 in.-lbs
8 in.-lbs
1 of 2
LOC B