TCFGP0G226M8R Rohm Semiconductor, TCFGP0G226M8R Datasheet - Page 4

• Manufacturer Part Number: TCFGP0G226M8R
• Description: CAP TANTALUM 22UF 4.0V 20% SMD
• Manufacturer: Rohm Semiconductor
• Series: TCFGr
• Type: Moldedr

Specifications of TCFGP0G226M8R

• Capacitance: 22µF
• Voltage - Rated: 4V
• Tolerance: ±20%
• Esr (equivalent Series Resistance): 7.700 Ohm
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 0805 (2012 Metric)
• Size / Dimension: 0.079" L x 0.049" W (2.00mm x 1.25mm)
• Height: 0.043" (1.10mm)
• Manufacturer Size Code: P
• Features: Fail Safe with Built-in Fuse
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Other names: 511-1487-2

○
TCFG Series P Case
Temperature
Stability
c
www.rohm.com
Surge
Voltage
Loading at
High
temperature
Terminal
Strength
Adhesiveness
2010 ROHM Co., Ltd. All rights reserved.
Item
Temp.
ΔC / C
tanδ
L.C
Temp.
ΔC / C
tanδ
L.C
Temp.
ΔC / C
tanδ
L.C
Appearance
L.C
ΔC / C
tanδ
Appearance
L.C
ΔC / C
tanδ
Capacitance
Appearance There should be no significant abnormality.
−55 °C
Within 0/−15%of initial value
Shall be satisfied the voltage on "Standard list"
+85 °C
Within +15/0%of initial value
Shall be satisfied the voltage on "Standard list"
Less than 1000% of initial limit
+125 °C
Within +20/0%of initial value
Shall be satisfied the voltage on "Standard list"
Less than 1250% of initial limit
There should be no significant abnormality.
Shall be satisfied the voltage on "Standard list"
Within
Less than 150% of initial limit
There should be no significant abnormality.
Less than initial limit
Within
Less than 150% of initial limit
The measured value should be stable.
The terminal should not come off.
±
±
10%of initial value
10%of initial value
Performance
−
4/6
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26 JIS C 5101-1
As per 4.14 JIS C 5101-3
Apply the specified surge voltage via the serial
resistance of 1kΩ every 5±0.5min.for 30±5 s. each
time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature
for over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 1000+36/0h
without discontinuation via the serial resistance
of 3Ω or less at a temperature of 85 ± 2 °C , leave
the sample at room temperature/humidity for
over 24h and measure the value.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends
to 1mm and by a prescribed tool maintain the
condition for 5s. (See the figure below.)
As per 4.34 JIS C 5101-1
As per 4.8 JIS C 5101-3
Apply force of 5N in the two directions shown
in the figure below for 10 ± 1s after mounting
the terminal on a circuit board.
Thickness 1.6mm
(based on JIS C5101-1 and JIS C5101-3)
Test conditions
50
45
R230
product
20
45
F (Apply force)
a circuit board
(Unit : mm)
1
Apply force
2010.01 - Rev.F
Data Sheet