PIC18F27J53-I/SP Microchip Technology, PIC18F27J53-I/SP Datasheet - Page 208

• Manufacturer Part Number: PIC18F27J53-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: *
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Embedded Interface Type: I2C, SPI, USART
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18(L)F2X/4XK22
The I
features:
• Master mode
• Slave mode
• Byte NACKing (Slave mode)
• Limited Multi-master support
• 7-bit and 10-bit addressing
• Start and Stop interrupts
• Interrupt masking
• Clock stretching
• Bus collision detection
• General call address matching
• Address masking
• Address Hold and Data Hold modes
• Selectable SDAx hold times
Figure 15-2
module in Master mode.
I
FIGURE 15-2:
DS41412D-page 208
2
C interface module in Slave mode.
2
C interface supports the following modes and
SDAx
SCLx
is a block diagram of the I
MSSPx BLOCK DIAGRAM (I
Figure 15-3
SDAx in
SCLx in
Bus Collision
is a diagram of the
2
C interface
Read
MSb
Generate (SSPxCON2)
Address Match Detect
Write Collision Detect
Preliminary
end of XMIT/RCV
Start bit, Stop bit,
State Counter for
Clock Arbitration
Start bit Detect,
Stop bit Detect
Acknowledge
SSPxBUF
SSPxSR
2
C™ MASTER MODE)
The PIC18(L)F2X/4XK22 has two MSSP modules,
MSSP1 and MSSP2, each module operating indepen-
dently from the other.
LSb
Note 1: In devices with more than one MSSP
Write
Clock
Data Bus
Shift
Internal
2: Throughout
Set/Reset: S, P, SSPxSTAT, WCOL, SSPxOV
Reset SEN, PEN (SSPxCON2)
Set SSPxIF, BCLxIF
module, it is very important to pay close
attention to SSPxCONx register names.
SSP1CON1 and SSP1CON2 registers
control different operational aspects of
the same module, while SSP1CON1 and
SSP2CON1 control the same features for
two different modules.
references to an MSSP module in any of
its operating modes may be interpreted
as being equally applicable to MSSP1 or
MSSP2. Register names, module I/O
signals, and bit names may use the
generic designator ‘x’ to indicate the use
of a numeral to distinguish a particular
module when required.
 2010 Microchip Technology Inc.
this
[SSPxM 3:0]
Baud Rate
Generator
(SSPxADD)
section,
generic