ATMEGA16A-AUR Atmel, ATMEGA16A-AUR Datasheet - Page 266

• Manufacturer Part Number: ATMEGA16A-AUR
• Description: MCU AVR 16KB FLASH 16MHZ 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA16A-AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

26.2.1
26.3
26.4
266
Signature Bytes
Calibration Byte
ATmega16A
Latching of Fuses
Table 26-4.
Notes:
The status of the Fuse bits is not affected by Chip Erase. Note that the Fuse bits are locked if
Lock bit1 (LB1) is programmed. Program the Fuse bits before programming the Lock bits.
The Fuse values are latched when the device enters programming mode and changes of the
Fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
All Atmel microcontrollers have a three-byte signature code which identifies the device. This
code can be read in both serial and parallel mode, also when the device is locked. The three
bytes reside in a separate address space.
For the ATmega16A the signature bytes are:
The ATmega16A stores four different calibration values for the internal RC Oscillator. These
bytes resides in the signature row High Byte of the addresses 0x0000, 0x0001, 0x0002, and
0x0003 for 1, 2, 4, and 8 Mhz respectively. During Reset, the 1 MHz value is automatically
loaded into the OSCCAL Register. If other frequencies are used, the calibration value has to be
loaded manually, see
Fuse Low
Byte
BODLEVEL
BODEN
SUT1
SUT0
CKSEL3
CKSEL2
CKSEL1
CKSEL0
1. $000: $1E (indicates manufactured by Atmel)
2. $001: $94 (indicates 16KB Flash memory)
3. $002: $03 (indicates ATmega16A device when $001 is $94)
4. Never ship a product with the OCDEN Fuse programmed regardless of the setting of Lock bits
5. If the JTAG interface is left unconnected, the JTAGEN fuse should if possible be disabled. This
1. The default value of SUT1:0 results in maximum start-up time.
2. The default setting of CKSEL3:0 results in internal RC Oscillator @ 1MHz. See
and the JTAGEN Fuse. A programmed OCDEN Fuse enables some parts of the clock system
to be running in all sleep modes. This may increase the power consumption.
to avoid static current at the TDO pin in the JTAG interface.
details.
page 25
Fuse Low Byte
Bit No.
7
6
5
4
3
2
1
0
for details.
“OSCCAL – Oscillator Calibration Register” on page 31
Description
Brown-out Detector trigger level
Brown-out Detector enable
Select start-up time
Select start-up time
Select Clock source
Select Clock source
Select Clock source
Select Clock source
Default Value
1 (unprogrammed)
1 (unprogrammed, BOD disabled)
1 (unprogrammed)
0 (programmed)
0 (programmed)
0 (programmed)
0 (programmed)
1 (unprogrammed)
SeeTable 8-9 on page 29
(1)
(2)
(2)
(2)
(1)
(2)
for details.
8154B–AVR–07/09
Table 8-1 on
for