ATMEGA645-16MU Atmel, ATMEGA645-16MU Datasheet - Page 222

• Manufacturer Part Number: ATMEGA645-16MU
• Description: IC AVR MCU FLASH 64K 64-QFN
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA645-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 53
• Program Memory Size: 64KB (32K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 2K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-MLF®, 64-QFN
• Processor Series: ATMEGA64x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 4 KB
• Interface Type: SPI, UART, USI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Package: 64MLF EP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATAVRISP2 - PROGRAMMER AVR IN SYSTEM
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

23.7
23.7.1
23.7.2
23.7.3
23.7.4
2570M–AVR–04/11
On-chip Debug Specific JTAG Instructions
PRIVATE0; 0x8
PRIVATE1; 0x9
PRIVATE2; 0xA
PRIVATE3; 0xB
A debugger, like the AVR Studio, may however use one or more of these resources for its inter-
nal purpose, leaving less flexibility to the end-user.
A list of the On-chip Debug specific JTAG instructions is given in
Instructions” on page
The JTAGEN Fuse must be programmed to enable the JTAG Test Access Port. In addition, the
OCDEN Fuse must be programmed and no Lock bits must be set for the On-chip debug system
to work. As a security feature, the On-chip debug system is disabled when either of the LB1 or
LB2 Lock bits are set. Otherwise, the On-chip debug system would have provided a back-door
into a secured device.
The AVR Studio enables the user to fully control execution of programs on an AVR device with
On-chip Debug capability, AVR In-Circuit Emulator, or the built-in AVR Instruction Set Simulator.
AVR Studio
poration’s AVR Assembler and C programs compiled with third party vendors’ compilers.
AVR Studio runs under Microsoft
For a full description of the AVR Studio, please refer to the AVR Studio User Guide. Only high-
lights are presented in this document.
All necessary execution commands are available in AVR Studio, both on source level and on
disassembly level. The user can execute the program, single step through the code either by
tracing into or stepping over functions, step out of functions, place the cursor on a statement and
execute until the statement is reached, stop the execution, and reset the execution target. In
addition, the user can have an unlimited number of code Break Points (using the BREAK
instruction) and up to two data memory Break Points, alternatively combined as a mask (range)
Break Point.
The On-chip debug support is considered being private JTAG instructions, and distributed within
ATMEL and to selected third party vendors only. Instruction opcodes are listed for reference.
Private JTAG instruction for accessing On-chip debug system.
Private JTAG instruction for accessing On-chip debug system.
Private JTAG instruction for accessing On-chip debug system.
Private JTAG instruction for accessing On-chip debug system.
®
supports source level execution of Assembly programs assembled with Atmel Cor-
222.
®
Windows
®
ATmega325/3250/645/6450
95/98/2000, Windows NT
“On-chip Debug Specific JTAG
®
and Windows XP
®
.
222