MC9S08GT16ACFBE Freescale Semiconductor, MC9S08GT16ACFBE Datasheet - Page 99

• Manufacturer Part Number: MC9S08GT16ACFBE
• Description: IC MCU 16K FLASH 2K RAM 44-QFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08GT16ACFBE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFP
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 40MHz
• Interface Type: I2C/SCI/SPI
• Total Internal Ram Size: 2KB
• # I/os (max): 36
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 44
• Package Type: PQFP
• Processor Series: S08GT
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Operating Supply Voltage: 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: M68EVB908GB60E, M68DEMO908GB60E
• Minimum Operating Temperature: - 40 C
• For Use With: M68DEMO908GB60E - BOARD DEMO MC9S08GB60M68EVB908GB60E - BOARD EVAL FOR MC9S08GB60
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

Chapter 7
Keyboard Interrupt (S08KBIV1)
7.1
The MC9S08GT16A/GT8A has one KBI module with eight keyboard interrupt inputs that share port A
pins. See
of these pins.
7.1.1
The following paragraphs discuss controlling the keyboard interrupt pins.
Port A is an 8-bit port which is shared among the KBI keyboard interrupt inputs and general-purpose I/O.
The eight KBIPEn control bits in the KBIPE register allow selection of any combination of port A pins to
be assigned as KBI inputs. Any pins which are enabled as KBI inputs will be forced to act as inputs and
the remaining port A pins are available as general-purpose I/O pins controlled by the port A data (PTAD),
data direction (PTADD), and pullup enable (PTAPE) registers.
KBI inputs can be configured for edge-only sensitivity or edge-and-level sensitivity. Bits 3 through 0 of
port A are falling-edge/low-level sensitive while bits 7 through 4 can be configured for
rising-edge/high-level or for falling-edge/low-level sensitivity.
The eight PTAPEn control bits in the PTAPE register allow you to select whether an internal pullup device
is enabled on each port A pin that is configured as an input. When any of bits 7 through 4 of port A are
enabled as KBI inputs and are configured to detect rising edges/high levels, the pullup enable bits enable
pulldown rather than pullup devices.
An enabled keyboard interrupt can be used to wake the MCU from wait or standby (stop3).
7.1.2
The keyboard interrupt (KBI) module features include:
Freescale Semiconductor
•
Keyboard interrupts selectable on eight port pins:
— Four falling-edge/low-level sensitive
— Four falling-edge/low-level or rising-edge/high-level sensitive
— Choice of edge-only or edge-and-level sensitivity
— Common interrupt flag and interrupt enable control
— Capable of waking up the MCU from stop3 or wait mode
Chapter 2, “Pins and
Introduction
Port A and Keyboard Interrupt Pins
Features
MCU Pin:
KBIP7
PTA7/
Connections,” for more information about the logic and hardware aspects
MC9S08GT16A/GT8A Data Sheet, Rev. 1
KBIP6
PTA6/
Figure 7-1. Port A Pin Names
KBIP5
PTA5/
PTA4/
KBIP4
PTA3/
KBIP3
PTA2/
KBIP2
PTA1/
KBIP1
PTA0/
KBIP0
99