M30873FHGP#U5 Renesas Electronics America, M30873FHGP#U5 Datasheet - Page 124

• Manufacturer Part Number: M30873FHGP#U5
• Description: IC M32C/87 MCU FLASH 100LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M32C/80r

Specifications of M30873FHGP#U5

• Core Processor: M32C/80
• Core Size: 16/32-Bit
• Speed: 32MHz
• Connectivity: CAN, EBI/EMI, I²C, IEBus, IrDA, SIO, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 384KB (384K x 8)
• Program Memory Type: FLASH
• Ram Size: 24K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 26x10b; D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-LQFP
• For Use With: R0K330879S001BE - KIT DEV RSK M32C/87R0K330879S000BE - KIT DEV RSK M32C/87
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

M32C/87 Group (M32C/87, M32C/87A, M32C/87B)
REJ09B0180-0151 Rev.1.51 Jul 31, 2008
Page 100 of 587
Table 9.7
Address bus, data bus, CS0 to CS3, BHE
RD, WR, WRL, WRH
HLDA, BCLK
ALE
Ports
CLKOUT
9.5.2.3
9.5.2.4
Table 9.7 lists pin states in wait mode.
Wait mode is exited by the hardware reset 1, hardware reset 2, NMI interrupt, Vdet4 detection interrupt, or
peripheral function interrupts.
As for a peripheral function interrupt that is not used to exit wait mode, set bits ILVL2 to ILVL0 in the
corresponding Interrupt Control Register to 000b (interrupt disabled) before executing the WAIT instruction.
The CM02 bit setting in the CM0 register affects the use of the peripheral function interrupts to exit wait mode.
When the CM02 bit is set to 0 (peripheral clocks do not stop in wait mode), any peripheral function interrupts
can be used to exit wait mode. When the CM02 bit is set to 1 (peripheral clocks stop in wait mode), the
peripheral functions clocked by the peripheral function clocks stop, and therefore, the peripheral function
interrupts cannot be used to exit wait mode. However, the peripheral functions clocked by the external clock
and fC32 do not stop regardless of the CM02 bit setting. Also, f2n, which uses the XIN clock (fXIND) or on-
chip oscillator clock as its clock source does not stop. The interrupts generated by the peripheral functions
which operate using these clocks can be used to exit wait mode.
When the MCU exits wait mode by the peripheral function interrupts or NMI interrupt, the CPU clock does not
change before and after the WAIT instruction is executed.
Table 9.8 lists interrupts to be used to exit wait mode and usage conditions.
Pin States in Wait Mode
Pin States in Wait Mode
Exiting Wait Mode
Pin
When fC is selected
When f8, f32 are selected • When the CM02 bit in the CM0 register is 0 (peripheral clocks
Maintain the state immediately
before entering wait mode
“H”
“H”
“L”
Maintain the state immediately before entering wait mode
Continue to output the clock
• When the CM02 bit is 1 (peripheral clock stops in wait mode):
do not stop in wait mode): Continue to output the clock
The clock is stopped and holds the level immediately before
entering wait mode
Memory Expansion Mode
Microprocessor Mode
9. Clock Generation Circuits
Single-Chip Mode